Find Parts That Fit Your Vehicle

BMW Catback Exhaust Systems

Catback Exhaust systems are designed to completely replace everything from your cats all the way back to your exhaust tips. Traditionally, if you are planning on upgrading your entire exhaust system, you will also need headers and downpipes.
Sort By:

Borla - Corporate Logo
T#:3517
Part#: 140084
In Stock at Vendor
$ 2,118.99 USD
Free Shipping
$ 2,118.99 USD
Free Shipping
Section: center section with resonator, rear muffler (header/cat-back)
Installation: bolt-on to header, clamps elsewhere
Tip Style: dual round 76mm Borla angle cut
Power Gain: +5hp

Borla completely re-engineers the exhaust on the E46 325/330 with a tuned all-stainless cat-back system. The E46 Borla bolts straight to the factory manifold and uses all of the factory hangers for an easy and seamless install. Your factory exhaust can come off as one complete piece and bolt this in its place! This is a full stainless system - T304 inside and out for maximum corrosion resistance. The Borla flows better than the stock system too for increased performance, even over the stock ZHP system. But we love the sound of this system the most - deep and with plenty of rumble to set it apart from the stock sound. It's a tuned system, with front resonator and rear muffler, to be louder than stock but not excessive. It's also a lot lighter than the stock system at only 33lbs from nose to tailpipe.

Read what Borla owners have to say:
"The difference over stock is noticeable the instant you turn the key. It begins with a deep muted rumble at engine start. Between 1200-2000rpm, you are treated to a nice throaty (and somewhat loud) growl. Between 2500-3500rpm, the deep growl reveals a slightly deeper, more melodic mechanical rev-up. Once past 4500rpm, the car begins to sound surprisingly stock, all the way up to redline. Lifting off the gas reveals a slightly more pronounced "burble" that settles into a low rumble as revs drop back to idle. At steady cruising speeds, the exhaust does not drone. Planting your right foot brings back that wonderful low growl."
"...the Borla is a very well built unit. Very civilized exhaust note... more agressive, yet not obnoxiously loud."
"I can easily say the Borla exhaust is much better than the X&X exhaust. My brother has the Borla on his 330i ZHP, and I had the X&X on my 330i. The X&X exhaust didn't have the quality of engineering compared to the Borla. The X&X was louder, and had horrible resonation - unacceptable for street use. The Borla is bolt-on, excellent quality, and hangs perfectly straight. The sound is a bit louder than stock, yet never "rice" or obnoxious."

Every Borla is made with 304 stainless steel for the internals and muffler body. Unlike other systems that can use coated aluminum, mild steel, or 409 stainless, the Borla uses true 304 stainless on the inside as well as the outside. This prevents the muffler from rusting and deteriorating from the inside out. Borla guarantees every muffler with a 1,000,000 mile warranty. Turner Motorsport has been the leading Borla dealer for BMW exhausts since we sold our first system in 1996, including using Borla Exhausts on all of every Turner BMW racecar.

This item fits the following BMWs:
2001-2005 E46 BMW 325i 325ci 330i 330ci
Show More Show Less
Supersprint - Corporate Logo
T#:189821
Part#: 781523-781506
Ships in 5 Business Days
$ 1,867.20 USD
Free Shipping
$ 1,867.20 USD
Free Shipping

Free ground shipping! 

This Supersprint performance exhaust is built from the Euro M5/M6 exhaust layout but fits the E24/E28 (see fitment notes below). It features oversized dual 50mm stainless steel pipes leading from the catalytic converter. This Supersprint system has a center resonator and rear muffler with free-flow designs for a sporty sound and less restriction to free up horsepower. Both systems are bolt-on to the stock factory catalytic converter (see fitment notes below) and use all of the stock hangers and gaskets. This makes for an excellent replacement exhaust system because the sound is such a great match to the M30 engine and retro cool that these cars have now. It's a classic growl and throaty sound without being overly aggressive. We've had nothing but compliments on the sound from this system. The previous mild steel versions have been discontinued - this system is now 100% T304 stainless steel!

Supersprint exhaust is widely recognized as the leader in complete exhaust system upgrades - extremely high quality, well designed for optimal flow, and amazing sound. Even at a premium price Supersprint is an unbeatable exhaust system because every aspect is done to such a high level. A Supersprint exhaust rewards you with a terrific sound, long lasting construction and excellent fitment. The Supersprint sound is very 'European' which fits the sporting sophistication of BMWs perfectly. Most systems are also modular - sections can be added or removed to custom tailor the exhaust sound to your preferance. Aside from 'Race' systems, their mufflers meet European noise laws so you get a refined and tuned sound without being excessively loud. Most Supersprint systems are built with larger diameter piping to improve exhaust flow which helps the engine do less work and make more horsepower! Supersprint exhausts generally run at a premium over other systems but no other system on the market can match their quality, performance, or reputation!

Fitment Notes: This rear muffler fits with the stock 535/635 US rear bumper.

  • 1982-1987 535/635 models should have a stock 3-bolt flange where the center resonator and front catalytic converter meet. This Supersprint system is a direct bolt-on replacement to this system. It has 3-bolt flanges.
  • 1988-1989 635 uses a 2-bolt flange on the stock cat section and that flange must be removed and replaced with the triangular 3-bolt flange (BMW p/n 18111178137) and gaskets (p/n 18301723886). Or remove the 3-bolt flanges from the Supersprint and re-weld the old 2-bolt flanges from the stock US resonator section.
  • 1985-1989 M5/M6 requires the complete Supersprint exhaust

section: center resonator + rear muffler
connects to: Supersprint center section or stock cat section*
tip style: 70mm dual round
material: T409 stainless steel (both sections)

To complete install will need connecting pipes T#397683

This item fits the following BMWs:
1982-1988 E28 BMW 535i 535is M5
1982-1989 E24 BMW 635CSi M6

Show More Show Less
AWE - Corporate Logo
T#:589702
Part#: GRP-EXH-BMF30340
Ships in 4 Business Days
Starting at $ 1,595.00 USD
Free Shipping
Starting at $ 1,595.00 USD
Free Shipping
The Touring Edition Exhaust for the F3X 340/440 from AWE offers a perfectly balanced and tuned exhaust that will deliver power when needed without droning at cruising speeds. By replacing the factory muffler, you will uncover the pure sound of the B58 twin-turbo engine. This exhaust is perfect for those who want a more aggressive response when getting on the throttle, but don't want to wake up the neighbors. Choose to include the AWE midpipe for even more weight savings and further increased flow and sound. Also choose between 90mm or 102mm tips in Chrome Silver or Diamond Black, or spring for the 96mm Carbon Fiber Tips. An Axleback Exhaust with Optional Midpipe.
Show More Show Less

Magnaflow - Corporate Logo
T#:189204
Part#: 16535-M
Ships in 1 Business Day
$ 908.00 USD
$ 908.00 USD

Enhance Performance and Durability with Magnaflow Stainless Steel Exhaust

Protect your exhaust system from the corrosive effects of road salt and moisture with a high-performance upgrade. Over time, stock exhausts succumb to rust, resulting in increased noise and vibration. Upgrade to a Magnaflow exhaust not only resolves these issues but also unleashes latent engine power by improving its airflow. Crafted entirely from 100% stainless steel, Magnaflow systems undergo stringent dyno testing, confirming their power-boosting capabilities. These exhausts boast mandrel bent construction and full welding for a seamless installation experience. Featuring a 5x8x18" polished muffler, this system delivers a smooth, deep tone paired with dual 3" tips.

Magnaflow 1991 BMW 325I L6 2.5L Single Rear Exit
Show More Show Less

Supersprint - Corporate Logo
T#:182582
Part#: 781523-781326-M
Ships in 5 Business Days
$ 1,780.80 USD
Free Shipping
$ 1,780.80 USD
Free Shipping

Free ground shipping!

This Supersprint performance exhaust is built from the Euro exhaust layout. It features oversized dual 50mm stainless steel pipes leading from the catalytic converter. This Supersprint system has a center resonator and rear muffler with free-flow designs for a sporty sound and less restriction to free up horsepower. The sound is such a great match to the M88/S38 engine and retro cool that these cars have now. It's a classic growl and throaty sound without being overly aggressive. We've had nothing but compliments on the sound from this system. The previous mild steel versions have been discontinued - this system is now 100% T304 stainless steel!

Supersprint exhaust is widely recognized as the leader in complete exhaust system upgrades - extremely high quality, well designed for optimal flow, and amazing sound. Even at a premium price Supersprint is an unbeatable exhaust system because every aspect is done to such a high level. A Supersprint exhaust rewards you with a terrific sound, long lasting construction and excellent fitment. The Supersprint sound is very 'European' which fits the sporting sophistication of BMWs perfectly. Most systems are also modular - sections can be added or removed to custom tailor the exhaust sound to your preferance. Aside from 'Race' systems, their mufflers meet European noise laws so you get a refined and tuned sound without being excessively loud. Most Supersprint systems are built with larger diameter piping to improve exhaust flow which helps the engine do less work and make more horsepower! Supersprint exhausts generally run at a premium over other systems but no other system on the market can match their quality, performance, or reputation!

Fitment Notes: This system is not a direct fit with the US catalytic converter section. The factory system is connected with 2-bolt flanges but the Supersprint Euro system is based on the Euro 3-bolt flanges. The US cat section flanges must be removed and replaced with the triangular 3-bolt flange (BMW p/n 18111178137) and gaskets (p/n 18301723886). Or, conversely, remove the 3-bolt flanges from the Supersprint and re-weld the old 2-bolt flanges from the stock resonator section.

section:center resonator + rear muffler

connects to:stock cat section*

tip style:80mm dual round

material:T409 stainless steel (both sections)


This item fits the following BMWs:
1988 E28 BMW M5
1987-1989 E24 BMW M6

Show More Show Less
AWE - Corporate Logo
T#:589673
Part#: GRP-EXH-BWM240
Ships in 4 Business Days
Starting at $ 1,435.00 USD
Free Shipping
Starting at $ 1,435.00 USD
Free Shipping
The Touring Edition Exhaust for the F22 M240 from AWE offers a perfectly balanced and tuned exhaust that will deliver power when needed without droning at cruising speeds. By replacing the factory muffler, you will uncover the pure sound of the B58 twin-turbo engine. This exhaust is perfect for those who want a more aggressive response when getting on the throttle, but don't want to wake up the neighbors. This system includes the AWE midpipe for even more weight savings and further increased flow and sound. Also choose between 90mm or 102mm tips in Chrome Silver or Diamond Black, or spring for the 96mm Carbon Fiber Tips.
Show More Show Less

Akrapovic - Corporate Logo
T#:9383747
Part#: M-BM/T/8HKTPDK
In Stock at Vendor
Starting at $ 7,034.99 USD
Starting at $ 7,034.99 USD
This axle-back exhaust system is manufactured entirely from titanium. This makes this system ideal for cutting weight while being structurally stronger than the OE exhaust system. The engineers at Akrapovic have retained the dual mode exhaust flap control from the original system. This allows the vehicle to have a more civilized, but deeper than stock sound at low speed. However, at higher RPM (or when selecting the S mode on the gearshift) the muffler is bypassed, creating a deep and sporty sound much more in keeping with the personality of the car. The included exhaust pipe tips are made completely from titanium OR a carbon fiber/titanium composite to add a high-end, refined style. Performance has not been left out of the design. The system dramatically reduces backpressure and is an excellent starting point for further engine tuning or turbo modifications. Even when installed on an otherwise stock vehicle a gain of 7.3 horsepower and 17.4 Nm/12.8 lbs-ft of torque are achieved. Furthermore, a weight reduction of 3.0 kg/6.6 lbs. is realized. The OEM catalysts are retained, so no reflashing of the ECU is required and the check engine light will not be triggered. Titanium muffler with integrated exhaust valves Statistics: +7.3 HP (at 4400 rpm) +17.4 Nm/12.8 lbs-ft of torque (at 2350 rpm) 3 kg/6.6 lbs. lighter than stock Not for sale outside the US or Canada.
Show More Show Less
Valvetronic Designs - Corporate Logo
T#:51110156
Part#: G90M5VSESTIBRT
Ships in 1 Business Day
New Item
$ 4,999.00 USD
Free Shipping
$ 4,999.00 USD
Free Shipping
The new G90 M5 may be heavy, it may be controversial, and from the factory, it may sound like a vacuum cleaner, but Valvetronic Designs is here to change that. Introducing the first and finest aftermarket exhaust system for the G90 M5, engineered to unleash the incredible sound potential of your 800+ HP super-sedan. Whether you’re in the mood for spine-tingling acceleration or quiet, refined cruising, our valved exhaust gives you full control over your car’s soundtrack. Designed and developed at Valvetronic's headquarters in Pennsylvania, USA, this system is built for the enthusiast who demands nothing but the best.
Show More Show Less

Valvetronic Designs - Corporate Logo
T#:40241322
Part#: G30M550IVSESBRRC
Ships in 1 Business Day
$ 2,999.00 USD
Free Shipping
$ 2,999.00 USD
Free Shipping
Unlock the full potential of your N63-powered BMW G30 M550i with the Valvetronic Designs Valved Exhaust System. Engineered for those who demand both performance and refinement, this system delivers a commanding exhaust note and enhanced driving dynamics, without sacrificing daily comfort.
Show More Show Less

Borla - Corporate Logo
T#:4176
Part#: 140276
In Stock at Vendor
$ 1,419.99 USD
$ 1,419.99 USD
Section: cat-back x-pipe, rear mufflers
Installation: slip-on
Tip Style: dual round 80mm Borla angle cut
Power Gain: +7hp

The Borla 'Aggressive' system for the E90/E92 335i is a cat-back system comprised of no resonators, x-pipe section, and dual rear mufflers. This system was Borla's response to a demand for greater volume for the 335's twin-turbo N54 motor. The turbos make the car quieter so having a performance exhaust will allow you to finally hear the engine. Borla has tuned this exhaust to give more of a throaty burble, especially at low RPM while maintaining acceptable sound levels for daily street use. This Borla system is perfect if you want to hear the exhaust but not annoy the people in the car next to you. And this is a true cat-back system so no catalytic converters or emissions equipment is affecting by installing this. And with a free-flowing design this will allow a modest bump in power output. The Borla system is also a lot lighter than the factory system; less weight = more performance!

Every Borla is made with 304 stainless steel for the internals and muffler body. Unlike other systems that can use coated aluminum, mild steel, or 409 stainless, the Borla uses true 304 stainless on the inside as well as the outside. This prevents the muffler from rusting and deteriorating from the inside out. Borla guarantees every muffler with a 1,000,000 mile warranty. Turner Motorsport has been the leading Borla dealer for BMW exhausts since we sold our first system in 1996, including using Borla Exhausts on every Turner BMW racecar.

This item fits the following BMWs:
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
Show More Show Less
Milltek Sport - Corporate Logo
T#:35391005
Part#: SSXBM1145
Ships in 3 Business Days
$ 740.99 USD
$ 740.99 USD
Milltek's Cat-Back systems are meticulously engineered for those looking to improve both the sound and appearance of their vehicle. Designed as direct replacements for the factory exhaust, these systems come in a range of configurations, giving owners the flexibility to adjust the exhaust volume and achieve a more aggressive tone that fits their style. Made from high-quality 304L Aircraft Grade stainless steel, Milltek’s Cat-Back systems are built to endure the toughest conditions, ensuring exceptional durability and long-lasting performance.
Show More Show Less
Milltek Sport - Corporate Logo
T#:6476053
Part#: F8XSPORT
Ships in 3 Business Days
Starting at $ 2,967.99 USD
Starting at $ 2,967.99 USD
Deciding on the right exhaust should include a blend of considerations: performance, quality, note, and style. The Milltek performance catback is a fantastic blend of these considerations. The performance and quality are top tier, with a note that is quite balanced. The system is constructed from aircraft-grade stainless steel that is beautiful to look at. These features and characteristics make the Milltek performance catback a great option.
Show More Show Less


Borla - Corporate Logo
T#:179780
Part#: 140509
Ships in 10 Business Days
$ 1,483.99 USD
Free Shipping
$ 1,483.99 USD
Free Shipping
Section: complete exhaust from the downpipe-back, non resonator, Borla performance muffler
Installation: clamp-on
Tip Style: dual round 80mm Borla angle cut
Power Gain: +6hp



This stainless steel rear exhaust section replaces the heavy (and restrictive) stock exhaust system on the F30 328i. Shed excess weight and restriction, and get a better sound! You will love the rich, deep sound this tuned system gives your 328i. There's a throaty and purposeful growl at low RPM and at cruise that makes you forget there's a four-cylinder under the hood. And if you have tuned your 328i to make more boost than stock, you will greatly appreciate the Borla design without the restrictive resonator and muffler.

Every Borla is made with 304 stainless steel for the internals and muffler body. Unlike other systems that can use coated aluminum, mild steel, or 409 stainless, the Borla uses true 304 stainless on the inside as well as the outside. This prevents the muffler from rusting and deteriorating from the inside out. Borla guarantees every muffler with a 1,000,000 mile warranty. Turner Motorsport has been the leading Borla dealer for BMW exhausts since we sold our first system in 1996, including using Borla Exhausts on every Turner BMW racecar.

This Borla Exhaust fits the following BMWs:
2012+ F30 BMW 328i - Sedan
Show More Show Less
Performance Street Cat Back - Titanium Tips - F22 M235i
Street version mufflers for a great tone without deafening noise.
Milltek Sport - Corporate Logo
T#:591422
Part#: SSXBM1028
Ships in 3 Business Days
$ 2,067.99 USD
Free Shipping
$ 2,067.99 USD
Free Shipping
With in-house production and engineering in the United Kingdom, they have been designing and developing exhaust systems for over 32 years. This experience has helped put Milltek on the map when it comes to performance exhausts, with offerings that range from Audi/Volkswagen to Porsche, BMW, and even Bentley. But, they don't stop there. Milltek has also made its presence felt in the motorsport community. Through partnerships with various race teams throughout the world, Milltek has gathered feedback on ways to improve their systems from enthusiasts at every level. Constructed of type-304 aircraft grade stainless steel, the quality is top-notch. To take it a step further, Milltek offers a lifetime warranty to the original purchaser.
Show More Show Less
Akrapovic - Corporate Logo
T#:3018043
Part#: P-HF1384
Ships in 3 Business Days
$ 605.99 USD
Free Shipping
$ 605.99 USD
Free Shipping

Akrapovic Sound Kit for BMW G80 G82 M3 M4 offers BMW owners the ability to control the sound of their Akrapovic exhaust system directly from the cockpit. Utilizing advanced Akrapovic technology, this kit allows drivers to switch between a quieter mode and a sportier exhaust sound. The system includes a receiver, already integrated into the Evolution exhaust system, which operates the actuators to open or close the exhaust valves. Drivers can manage the sound with the Sound Remote Controller or the latest smartphone app, compatible with both iOS and Android devices.

  • Enhanced Control: Allows for easy switching between quiet and sporty exhaust modes.
  • Advanced Technology: Features Akrapovic technology for precise sound management.
  • Convenient Operation: Control the exhaust valves using the Sound Remote Controller or a smartphone app.
  • Compatibility: Designed specifically for BMW G80 and G82 M3 and M4 models.
  • Easy Integration: Receiver included in the Evolution system for straightforward installation.
Show More Show Less

Supersprint - Corporate Logo
T#:588989
Part#: TMSE31840SS
Back Ordered
Starting at $ 2,885.98 USD
Starting at $ 2,885.98 USD
Supersprint exhaust is widely recognized as the leader in complete exhaust system upgrades - extremely high quality, well designed for optimal flow, and amazing sound. Even at a premium price, Supersprint is an unbeatable exhaust system because every aspect is done to such a high level. A Supersprint exhaust rewards you with a terrific sound, long-lasting construction, and excellent fitment. The Supersprint sound is very 'European' which fits the sporting sophistication of BMWs perfectly. Most systems are also modular - sections can be added or removed to custom tailor the exhaust sound to your preference. Aside from 'Race' systems, their mufflers meet European noise laws so you get a refined and tuned sound without being excessively loud. Supersprint exhausts generally run at a premium over other systems but no other system on the market can match their quality, performance, or reputation!
Show More Show Less

AWE - Corporate Logo
T#:589686
Part#: F30-335-GROUP
Ships in 4 Business Days
Starting at $ 1,595.00 USD
Free Shipping
Starting at $ 1,595.00 USD
Free Shipping
The Touring Edition Exhaust for the F3X 335/435 from AWE offers a perfectly balanced and tuned exhaust that will deliver power when needed without droning at cruising speeds. By replacing the factory muffler, you will uncover the pure sound of the N55 twin-turbo engine. This exhaust is perfect for those who want a more aggressive response when getting on the throttle, but don't want to wake up the neighbors. Choose to include the AWE midpipe for even more weight savings and further increased flow and sound. Also choose between 90mm or 102mm tips in Chrome Silver or Diamond Black, or spring for the 96mm Carbon Fiber Tips. An Axleback Exhaust with Optional Midpipe.
Show More Show Less
Magnaflow - Corporate Logo
T#:189234
Part#: 16859-M
Ships in 1 Business Day
$ 2,462.00 USD
$ 2,462.00 USD
Magnaflow systems are made from 100% stainless steel and are dyno tested and proven to make power. All Magnaflow exhaust are mandrel bent and fully welded for trouble a free installation. This system uses 5x8x14" polished mufflers with round resonators for a smooth deep tone with quad 4" double rolled edge tips. Includes clamps, hangers, and detailed instructions.
Show More Show Less

Magnaflow - Corporate Logo
T#:189201
Part#: 16532-M
Ships in 1 Business Day
$ 1,396.00 USD
$ 1,396.00 USD
Unlock the performance potential with Magnaflow exhaust systems, meticulously crafted from premium 100% stainless steel. These dyno-tested systems have proven power-boosting capabilities. Featuring mandrel bending and full welding, Magnaflow exhausts guarantee a seamless installation experience. Equipped with a 5x8x14" polished muffler, this system produces a smooth, deep tone, accompanied by dual 3" double rolled edge tips. The package includes clamps, hangers, and detailed installation instructions for convenience.
Show More Show Less
AWE - Corporate Logo
T#:9383751
Part#: 3025-43074PDK
Ships in 4 Business Days
Starting at $ 2,775.00 USD
Free Shipping
Starting at $ 2,775.00 USD
Free Shipping
The SwitchPath Catback Exhaust for the F80 M3/M4 from AWE offers a perfectly balanced and tuned exhaust that will deliver power when needed without droning at cruising speeds. By replacing the factory muffler, you will uncover the pure sound of the S55 engine. This exhaust is perfect for those who want a more aggressive response when getting on the throttle, but don't want to wake up the neighbors. The SwitchPath™ Technology utilizes factory valving and M-Sport button to adjust tone on the fly. Other Features Include: Chrome Silver OR Black Diamon Finish tips Max gains of 20 hp and 31 ft-lbs of torque at the crank Clean, non-raspy S55 tone Handcrafted from 3” CNC mandrel-bent, U.S.-made .065” wall T304L stainless steel Precision-engineered integrated X-pipe Direct bolt on, no cutting Perfect fitment guaranteed AWE No CEL guarantee Lifetime warranty Proudly engineered, designed, and manufactured in-house at AWE
Show More Show Less

Eisenmann Performance Sport Exhaust - F3X 340/440
Modification of the Rear Bumper Required w/ 4x76mm tips
Eisenmann - Corporate Logo
T#:584790
Part#: B5455.00902KT
Back Ordered
Starting at $ 1,895.00 USD
Free Shipping
Starting at $ 1,895.00 USD
Free Shipping
Maximize performance and style with massive weight savings

Milltek Sport - Corporate Logo
T#:380512
Part#: SSXBM948
Ships in 3 Business Days
$ 1,456.00 USD
Free Shipping
$ 1,456.00 USD
Free Shipping
With in-house production and engineering in the United Kingdom, they have been designing and developing exhaust systems for over 32 years. This experience has helped put Milltek on the map when it comes to performance exhausts, with offerings that range from Audi/Volkswagen to Porsche, BMW, and even Bentley. But, they don't stop there. Milltek has also made its presence felt in the motorsport community. Through partnerships with various race teams throughout the world, Milltek has gathered feedback on ways to improve their systems from enthusiasts at every level. Constructed of type-304 aircraft grade stainless steel, the quality is top-notch. To take it a step further, Milltek offers a lifetime warranty to the original purchaser.
Show More Show Less
Active Autowerke - Corporate Logo
T#:397446
Part#: 11-015
Ships in 3 Business Days
$ 1,519.99 USD
$ 1,519.99 USD

True performance, durability, and attractive weight advantages with innovative features places the Active Autowerke E9X BMW M3 exhaust in a class of its own. This system is constructed from 100% 304-stainless steel and features adjustable Active Autowerke double walled tips, making it ideal both for 2-door and 4-door models (also allows for cleaner fitment with diffusers).

This system uses factory style flanges making it a complete bolt on system that requires no cutting or welding. The system is a straight-through design providing substantial improvements to gas flow over the factory exhaust.

The sound is unobtrusive, with a rich mellow tone and delivers a solid 5+hp, with key gains in the mid-range. In addition, the Active Autowerke E9X M3 Signature Exhaust system features large 3" piping for maximum exhaust flow while maintaining enough back-pressure to result in horsepower increases across the entire RPM range.

The factory E9X M3 muffler features a Noise Canceling Chamber inside the muffler and Active Autowerke has retained this feature by adding two custom Active Autowerke noise canceling chambers (NCC)on each muffler to reduce/minimize the drone (the 'booming' noise some muffler emit at cruising speeds, ~3500 rpm).

The Active Autowerke E9X M3 Signature Exhaust System provides increase in horsepower, great sound and appearance making it a must for the true M3 enthusiasts.


Features:

  • Large 3-inch mandrel bent piping for maximum flow 
  • Durable, 100% 304 brushed stainless steel 
  • Double-walled 76mm Signature stainless tips
  • Revolutionary NCC -Noise Cancelling Chamber 
  • Adjustable Tips with Embossed Active Autowerke Logo
  • Improved power & torque throughout entire RPM band 
  • Gains of 5+ HP over stock configuration; Additional HP with our programmed software 
  • BMW factory style hardware makes a truly easy installation with no need for cutting or re-welding 
  • Weighs 40 Lbs vs. the factory of 55.1 Lbs.
  • Complete illustrated instruction manual
  • Two year warranty
Show More Show Less
Borla - Corporate Logo
T#:180925
Part#: 140580
In Stock at Vendor
$ 1,675.99 USD
$ 1,675.99 USD
Section: complete exhaust from the downpipe-back, non resonator, Borla performance muffler
Installation: clamp-on
Tip Style: round 88mm Borla angle cut


This stainless steel rear exhaust section replaces the heavy (and restrictive) stock exhaust system on the F30 335i F32 435i. Shed excess weight and restriction, and get a better sound! The ATAK system -- Acoustically Tuned Applied Kinetics -- allows a very high volume without drone and distortion. This is beyond the usual 'muscle car' sound - this is full blown automotive thunder! Borla manages the sound waves inside the exhaust to produce an exhaust note that maintains its tone as revs rise. With ATAK, the sound output is tuned like a graphic equalizer to shape and focus sound waves for optimum high-volume output. This exclusive technology produces the highest available dB (decibel) levels in the Borla street-legal lineup, and is designed for high-performance purists who prefer exhaust notes over their stereos. And if you have tuned your 335i to make more boost than stock, you will greatly appreciate the Borla design without the restrictive resonator and muffler.

Every Borla is made with 304 stainless steel for the internals and muffler body. Unlike other systems that can use coated aluminum, mild steel, or 409 stainless, the Borla uses true 304 stainless on the inside as well as the outside. This prevents the muffler from rusting and deteriorating from the inside out. Borla guarantees every muffler with a 1,000,000 mile warranty. Turner Motorsport has been the leading Borla dealer for BMW exhausts since we sold our first system in 1996, including using Borla Exhausts on every Turner BMW racecar.

This Borla Exhaust fits the following BMWs:
2012+ F30 BMW 335i - Sedan
2013+ F32 BMW 435i - Coupe
2013+ F33 BMW 435i Convertible
Show More Show Less


Akrapovic - Corporate Logo
T#:340330
Part#: TMS4781
In Stock at Vendor
Sale - Save 4% $ 5,403.99

This product was last offered at the strikethrough price on
07-06-2026

Starting at $ 5,199.79 USD
Free Shipping
Sale - Save 4%
$ 5,403.99

This product was last offered at the strikethrough price on
07-06-2026

Starting at $ 5,199.79 USD
Free Shipping
According to BMW the 1 Series M Coupe is a "predator on the prowl", why not give it some GROWL with the Akrapovic slip-on exhaust system.

This slip-on muffler is an "axle back" system that is mounted on the MotoGP 1M Coupe Safety Car and now is available for street going 1M Coupes. The Akrapovic Slip-On Titanium exhaust system for the BMW 1M Coupe is designed for drivers who demand more power and less weight. In addition to a weight reduction and a power gain, one of the tasks of the Akrapovic team was also to make the sound of the 1M Coupe become music to ones ears. An optional wireless "dualmode" exhaust flap control allows the vehicle to have a more civilized, but deeper than stock sound at low speed. However, when the exhaust flap is opened the muffler is bypassed, creating a deep and sporty sound much more in keeping with the personality of the car.

Not for sale outside the US or Canada.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe
Show More Show Less
Scorpion - Corporate Logo
T#:584753
Part#: SBM061M
Ships in 2 Business Days
$ 1,021.99 USD
$ 1,021.99 USD
This cat-back system from Scorpion features larger diameter piping for a freer flowing exhaust pathway.
Dinan - Corporate Logo
T#:19395571
Part#: D660-0096-BLK
Ships on Sep 29, 2026
11% off MSRP $ 1,968.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,749.99 USD
Free Shipping
11% off MSRP
$ 1,968.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,749.99 USD
Free Shipping
Evoke passion and excitement with the Dinan Valved exhausts for the GR Supra! Conveying the sweet sounds of a deep, rich, euphonious note that are unmistakably Dinan in addition to retaining the flexibility of valves, Dinan exhausts are the epitome of sound without sacrifice. Utilizing factory cut points and mounting mechanics, the Dinan exhaust system is a straightforward install with precision fitment just like you would expect straight from the manufacturer. Mounting and proper fitment is where the similarities to the factory exhaust end, however. Fabricated from brushed 100% T304 stainless steel, TIG welded and free of hydroformed pipe, the upgraded system is a marked improvement from its predecessor - both in terms of material/construction as well as in overall looks. For weight savings and simplicity, the stock single to dual pipe setup has been abandoned in favor of an enlarged, free flowing single pipe system. This pathway feeds into a muffler that limits frequencies associated with drone, as well as assists in altering the overall tone of the setup to deliver the signature low Dinan rumble. The no-nonsense design allows shocking versatility in sound levels when paired with features, like valves, often associated with more fanciful alternatives. The unabashedly spartan, yet effective, pipe layout forces gasses to escape from the rear out of massive dual, straight cut, 114.3 mm (4.5-inch) exhaust tips emblazoned with the laser engraved Dinan logo. The tip branding further cementing any lingering doubt that the system visible is something above and beyond stock-- if it was not already apparent by the blissful music permeating from them. Unquestionable enhancements to the overall chorus emitted through the Dinan system transcend all modes making the vehicle a delight to drive and enjoy. However, for those that wish to have options to limit the extraordinary soundtrack for late night or early morning arrivals/departures (or any number of other reasons) factory valve control is retained. This effectively makes the system behave similarly to a straight-pipe system that promotes maximum flow and volume when the valve is open and emit more subdued resonant vocals when the valve is closed, and exhaust gases are wholly redirected through the muffler. It is the perfect blend of civility when not pushing the car or the full spectrum of auditory delight when in it. No matter the situation, the Dinan valved cat-back exhaust system is the answer for the discerning enthusiast looking for sound without sacrifice. Features: Maximum gains of +6 HP and +5 ft-lb of torque Enjoyably louder, sportier sound Drone abatement technologies used to reduce cabin resonance Dual 4.5-inch (114.3mm) double-walled, black ceramic coated clamp-on tips with laser engraved Dinan logo Larger diameter piping for increased flow (83mm throughout primary run vs. 80mm at largest point) Factory resonator/collector removed for increased volume 10-pounds lighter than the stock system (Stock: 56-pounds vs. Dinan: 46-pounds) 100% 304 Stainless Steel construction Retains factory valve control Factory-like fitment with included mounting hardware
Show More Show Less

AWE - Corporate Logo
T#:589677
Part#: F30-320-EXH-GROU
In Stock
Starting at $ 1,325.00 USD
Free Shipping
Starting at $ 1,325.00 USD
Free Shipping
The Touring Edition Exhaust for the F30 320i from AWE offers a perfectly balanced and tuned exhaust that will deliver power when needed without droning at cruising speeds. By replacing the factory muffler, you will shed new light upon the turbocharged N20 engine. This exhaust is perfect for those who want a more aggressive response when getting on the throttle, but don't want to wake up the neighbors. This system includes the AWE midpipe for even more weight savings and further increased flow and sound. Also choose between 90mm or 102mm tips in Chrome Silver or Diamond Black.
Show More Show Less

Performance Street Cat Back - Black Tips - F22 M235i
Street version mufflers for a great tone without deafening noise.
Milltek Sport - Corporate Logo
T#:381384
Part#: SSXBM988
Ships in 3 Business Days
$ 1,868.99 USD
Free Shipping
$ 1,868.99 USD
Free Shipping
With in-house production and engineering in the United Kingdom, they have been designing and developing exhaust systems for over 32 years. This experience has helped put Milltek on the map when it comes to performance exhausts, with offerings that range from Audi/Volkswagen to Porsche, BMW, and even Bentley. But, they don't stop there. Milltek has also made its presence felt in the motorsport community. Through partnerships with various race teams throughout the world, Milltek has gathered feedback on ways to improve their systems from enthusiasts at every level. Constructed of type-304 aircraft grade stainless steel, the quality is top-notch. To take it a step further, Milltek offers a lifetime warranty to the original purchaser.
Show More Show Less
AWE - Corporate Logo
T#:598921
Part#: 3810-43020
Ships in 4 Business Days
$ 745.00 USD
$ 745.00 USD
Did you opt for the OE style tips when upgrading your exhaust? This kit allows you to swap out the OE style finisher with a beautiful Quad setup finished in Chrome silver. This will give the vehicle a more aggressive look!
Show More Show Less

AFE - Corporate Logo
T#:373978
Part#: 4946309
Ships in 3 Business Days
$ 1,532.00 USD
$ 1,532.00 USD

The MACH Force XP exhaust system for the BMW 325i/ci 330i/ci E46 produced 13 horsepower and 15 lbs. x ft. of torque. This exhaust system is constructed from 2.25” mandrel bent 409 stainless steel and is MIG-welded for high strength. The system uses a true dual in and dual out high flow muffler with 2.25” tubing which improves performance across the entire power band while maintaining a great tone. To finish off this exhaust are dual, double wall resonated angle cut 304 stainless steel tips. This exhaust uses all factory hanger locations for a hassle-free installation. No modifications necessary. 

Hassle-Free Installation: All systems use factory mounting locations providing stability and hassle-free installation.

Leak-Free Seal: High quality OE style flanges and band clamps are used for a complete 360 degree sealing surface.

Aggressive Sound: A free-flowing, true dual muffler is used to absorb high pitch tones producing a powerful sound and unleashing all available horsepower and torque.

OEM BMW Gaskets: This system uses two OEM BMW gaskets to provide a flawless seal without sacrificing quality.

All aFe exhaust systems are engineered and manufactured in our Corona, California manufacturing facility.

This part fits the following BMWs:
1998 - 2001 E46 325i 325ci 330i 330ci 

Show More Show Less
Supersprint - Corporate Logo
T#:589358
Part#: E36328SS
Ships on Dec 7, 2026
Starting at $ 6,741.98 USD
Starting at $ 6,741.98 USD
Supersprint exhaust is widely recognized as the leader in complete exhaust system upgrades - extremely high quality, well designed for optimal flow, and amazing sound. Even at a premium price, Supersprint is an unbeatable exhaust system because every aspect is done to such a high level. A Supersprint exhaust rewards you with a terrific sound, long-lasting construction, and excellent fitment. The Supersprint sound is very 'European' which fits the sporting sophistication of BMWs perfectly. Most systems are also modular - sections can be added or removed to custom tailor the exhaust sound to your preference. Aside from 'Race' systems, their mufflers meet European noise laws so you get a refined and tuned sound without being excessively loud. Supersprint exhausts generally run at a premium over other systems but no other system on the market can match their quality, performance, or reputation!
Show More Show Less

Magnaflow - Corporate Logo
T#:189195
Part#: 16525-M
Ships in 1 Business Day
$ 1,150.00 USD
$ 1,150.00 USD
Finding the right exhaust system for your vehicle can be difficult, but MagnaFlow has you covered. The Touring Series Stainless Performance Exhaust system delivers dyno-proven power with a comfortable interior sound and performance exterior sound. Constructed entirely of stainless steel, this exhaust will resist rusting and corroding, lasting many times longer than you stock exhaust! Specifications: Type: Cat-Back Series: Touring Main Piping Diameter: 2.5" Exit Style: Dual Straight Driver Side Rear Inlet Connection Type: Clamp-On Muffler Quantity: 2 Muffler Type: Straight-Through Muffler Material: Stainless Steel
Show More Show Less

Active Autowerke - Corporate Logo
T#:397486
Part#: 11-045
Ships in 3 Business Days
$ 3,563.00 USD
Free Shipping
$ 3,563.00 USD
Free Shipping
The Active Autowerke F8X rear exhaust was carefully engineered to eliminate the unflattering sound of the factory M3 and M4 exhaust, while also allowing for optimum flow and resonance. Every effort was made in addressing the not so appeasing sound of the stock OEM exhaust, but in designing an exhaust worthy for an "M" car. We believe our rear exhaust combined with our mid-pipe offers the deepest sound and best performance of any other system on the market today. Available for both models, this axle-back exhaust gives your BMW the deep, throaty, growl a car of its caliber should have had from the factory!
Show More Show Less
Milltek Sport - Corporate Logo
T#:380505
Part#: SSXBM941
Ships in 3 Business Days
$ 1,948.99 USD
Free Shipping
$ 1,948.99 USD
Free Shipping
With in-house production and engineering in the United Kingdom, they have been designing and developing exhaust systems for over 32 years. This experience has helped put Milltek on the map when it comes to performance exhausts, with offerings that range from Audi/Volkswagen to Porsche, BMW, and even Bentley. But, they don't stop there. Milltek has also made its presence felt in the motorsport community. Through partnerships with various race teams throughout the world, Milltek has gathered feedback on ways to improve their systems from enthusiasts at every level. Constructed of type-304 aircraft grade stainless steel, the quality is top-notch. To take it a step further, Milltek offers a lifetime warranty to the original purchaser.
Show More Show Less
Supersprint - Corporate Logo
T#:182583
Part#: 781523-781326
Ships in 5 Business Days
$ 2,354.40 USD
Free Shipping
$ 2,354.40 USD
Free Shipping

Free ground shipping! 

This Supersprint performance exhaust is built from the Euro M5/M6 exhaust layout but fits the non-M E24/E28 (see fitment notes below). It features oversized dual 50mm stainless steel pipes leading from the catalytic converter. This Supersprint system has a center resonator and rear muffler with free-flow designs for a sporty sound and less restriction to free up horsepower. Both systems are bolt-on to the stock factory catalytic converter (see fitment notes below) and use all of the stock hangers and gaskets. This makes for an excellent replacement exhaust system because the sound is such a great match to the M30 engine and retro cool that these cars have now. It's a classic growl and throaty sound without being overly aggressive. We've had nothing but compliments on the sound from this system. The previous mild steel versions have been discontinued - this system is now 100% T304 stainless steel!

Supersprint exhaust is widely recognized as the leader in complete exhaust system upgrades - extremely high quality, well designed for optimal flow, and amazing sound. Even at a premium price Supersprint is an unbeatable exhaust system because every aspect is done to such a high level. A Supersprint exhaust rewards you with a terrific sound, long lasting construction and excellent fitment. The Supersprint sound is very 'European' which fits the sporting sophistication of BMWs perfectly. Most systems are also modular - sections can be added or removed to custom tailor the exhaust sound to your preferance. Aside from 'Race' systems, their mufflers meet European noise laws so you get a refined and tuned sound without being excessively loud. Most Supersprint systems are built with larger diameter piping to improve exhaust flow which helps the engine do less work and make more horsepower! Supersprint exhausts generally run at a premium over other systems but no other system on the market can match their quality, performance, or reputation!

Fitment Note 1 (flanges):
1982-1988 635, 1984-1988 535 models should have a stock 3-bolt flange where the center resonator and front catalytic converter meet. This Supersprint system is a direct bolt-on replacement to this system.
1988-1989 635 BMW changed the center resonator and cat flanges from a 3-bolt triangle to a 2-bolt diamond-shaped flange. The Supersprint center resonator uses the 3-bolt flange. So you must either cut off the 3-bolt flange and reinstall the original 2-bolt flange. Or cut the 2-bolt flange from the cat and weld on a new 3-bolt flange (BMW p/n 18111178137 and gaskets p/n 18301723886, available separately).

Fitment Note 2 (hangers):
This system was originally designed for the Euro E24/E28 which does not have the rear hanger attachment over the tips like on a US model (you will need the Euro hanger setup). In addition the tips are shorter on the Euro muffler since the Euro bumpers do not extend as far as the US bumpers. So the tips on this muffler will sit just past the valance but tucked far under the bumper.
 

section:center resonator + rear muffler

connects to:stock cat section*

tip style:80mm dual round

material:T409 stainless steel (both sections)


This item fits the following BMWs:
1982-1988 E28 BMW 535i 535is
1982-1989 E24 BMW 635CSi

Show More Show Less


Supersprint - Corporate Logo
T#:34616672
Part#: 043620
Ships in 3 Business Days
$ 1,731.99 USD
Free Shipping
$ 1,731.99 USD
Free Shipping

Racer's Pack For BMW E36 M3 is the ultimate performance upgrade kit for E36 M3 enthusiasts, combining top-tier components to enhance power, handling, and reliability. Designed for precision and built to withstand the demands of high-performance driving, this pack includes carefully selected parts tailored to bring out the best in your BMW E36 M3. Offered by Turner Motorsport, this kit ensures peak performance on the track or street, with each component crafted for compatibility and durability.

  • Enhanced Engine Power: Boosts horsepower and torque, providing faster acceleration and a thrilling driving experience.
  • Improved Handling: Upgrades suspension components to optimize stability and cornering precision.
  • Perfect Fitment: Each part is engineered specifically for the BMW E36 M3, ensuring seamless integration and easy installation.
  • Track-Ready Durability: Crafted from high-quality materials to withstand extreme conditions, extending component life.
  • Trusted by BMW Enthusiasts: Offered through Turner Motorsport, a leader in BMW performance parts.

Unlock the full potential of your BMW E36 M3 with the Racer's Pack, a comprehensive solution for enthusiasts seeking peak performance and superior handling.

Show More Show Less
Corsa - Corporate Logo
T#:342217
Part#: COR14559S
Ships on Sep 24, 2026
$ 1,138.99 USD
$ 1,138.99 USD

Upgrade your BMW E46 with the Turner Motorsport Corsa Axle-Back Sport Mufflers featuring polished silver tips. Engineered with advanced technologies, Corsa exhaust systems deliver an unmistakable exhaust note while reducing restrictions for enhanced performance. Whether driving aggressively or lightly, these mufflers offer a perfect balance of sound and performance. Here are the key features:

  • Customized exhaust system for optimal vehicle performance
  • Aggressive exhaust note without drone
  • Dual personalities: throaty and charismatic under aggressive driving, subtle sporty sound under light driving
  • Full cat-back system for maximum performance
  • 3" dual round polished stainless tips for a stylish appearance
  • Constructed from T304 stainless steel for durability
  • Made in the USA
  • Backed by a lifetime warranty
Show More Show Less
Supersprint - Corporate Logo
T#:217652
Part#: TMS217652
Ships on Dec 7, 2026
$ 2,767.99 USD
Free Shipping
$ 2,767.99 USD
Free Shipping

Free ground shipping! 

The Supersprint rear mufflers for the turbo Z4 is a subtle sound and performance improvement for those that think the stock muffler is too tame. This sport rear muffler is a free-flowing design with larger piping to improve flow and tune the sound. With the stock cats in place the sound is still subdued but the Supersprint muffler makes an alteration to the exhaust note to be a little more sporty and aggressive but not intrusive or obnoxious. This system includes the center X-pipe with slightly oversized piping for improved flow over the stock system. The tips on the system are similar to the factory single round tips but slightly bigger so they fill out the bumper better and look more sporting.

Supersprint exhaust is widely recognized as the leader in complete exhaust system upgrades - extremely high quality, well designed for optimal flow, and amazing sound. Even at a premium price Supersprint is an unbeatable exhaust system because every aspect is done to such a high level. A Supersprint exhaust rewards you with a terrific sound, long lasting construction and excellent fitment. The Supersprint sound is very 'European' which fits the sporting sophistication of BMWs perfectly. Most systems are also modular - sections can be added or removed to custom tailor the exhaust sound to your preferance. Aside from 'Race' systems, their mufflers meet European noise laws so you get a refined and tuned sound without being excessively loud. Most Supersprint systems are built with larger diameter piping to improve exhaust flow which helps the engine do less work and make more horsepower! Supersprint exhausts generally run at a premium over other systems but no other system on the market can match their quality, performance, or reputation!

section:center x-pipe + rear mufflers

connects to:factory secondary cats

tip style:90mm single round per side

material:T304 stainless steel


This item fits the following BMWs:
2009+ Z4 BMW Z4 sDrive35i Z4 sDrive35is

Show More Show Less

Borla - Corporate Logo
T#:183998
Part#: 140505
In Stock at Vendor
$ 1,393.99

This product was last offered at the strikethrough price on
04-09-2026

$ 1,291.99 USD
$ 1,291.99 USD
Section: cat-back rear mufflers
Installation: slip-on
Tip Style: dual round 80mm Borla angle cut


The Borla Touring system for the E90 328i is a cat-back system comprised of a resonated center pipe and rear muffles. This system was Borla's response to a demand for greater volume for the 328i's N52 motor. Borla has tuned this exhaust to give more of a throaty burble, especially at low RPM while maintaining acceptable sound levels for daily street use. This Borla system is perfect if you want to hear the exhaust but not annoy the people in the car next to you. And this is a true cat-back system so no catalytic converters or emissions equipment is affecting by installing this. And with a free-flowing design this will allow a modest bump in power output. The Borla system is also a lot lighter than the factory system; less weight = more performance!

Every Borla is made with 304 stainless steel for the internals and muffler body. Unlike other systems that can use coated aluminum, mild steel, or 409 stainless, the Borla uses true 304 stainless on the inside as well as the outside. This prevents the muffler from rusting and deteriorating from the inside out. Borla guarantees every muffler with a 1,000,000 mile warranty. Turner Motorsport has been the leading Borla dealer for BMW exhausts since we sold our first system in 1996, including using Borla Exhausts on every Turner BMW racecar.

This item fits the following BMWs:
2006-2012 E90 BMW 328i 328xi 328i xDrive - Sedan
Show More Show Less

Supersprint - Corporate Logo
T#:338494
Part#: 784703-784746
Ships on Dec 7, 2026
Starting at $ 2,065.99 USD
Free Shipping
Starting at $ 2,065.99 USD
Free Shipping

Free ground shipping! 

Add a little more growl and sporty exuberance to the E32 740 with the Supersprint performance exhaust. This cat-back system has a tuned center resonator and sport muffler. Both are freer flowing than the stock 740 exhaust which gives a more sport-oriented sound and a modest power increase thanks to less restriction. Supersprint exhausts are often found on restored classic BMWs as a mild sport exhaust, thanks to their OEM quality and refined sound. The complete system is stainless steel and a direct fit to the stock catalytic converters (with the appropriate adapter pipe for the SWB or LWB).

Supersprint exhaust is widely recognized as the leader in complete exhaust system upgrades - extremely high quality, well designed for optimal flow, and amazing sound. Even at a premium price Supersprint is an unbeatable exhaust system because every aspect is done to such a high level. A Supersprint exhaust rewards you with a terrific sound, long lasting construction and excellent fitment. The Supersprint sound is very 'European' which fits the sporting sophistication of BMWs perfectly. Most systems are also modular - sections can be added or removed to custom tailor the exhaust sound to your preferance. Aside from 'Race' systems, their mufflers meet European noise laws so you get a refined and tuned sound without being excessively loud. Most Supersprint systems are built with larger diameter piping to improve exhaust flow which helps the engine do less work and make more horsepower! Supersprint exhausts generally run at a premium over other systems but no other system on the market can match their quality, performance, or reputation!

Fitment note: the resonator and muffler are the same for the 740i (SWB) and 740iL (LWB). But choose the correct adapter pipes below.

section:center resonator + rear muffler

connects to:stock cat section (see fitment note above)

tip style:90mm dual round

material:T304 stainless steel (both sections)


This item fits the following BMWs:
1993-1994 E32 BMW 740i 740iL

Show More Show Less
Corsa - Corporate Logo
T#:26638247
Part#: 14569BLK
Back Ordered
8% off MSRP $ 2,923.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 2,682.99 USD
Free Shipping on orders $49 and up
8% off MSRP
$ 2,923.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 2,682.99 USD
Free Shipping on orders $49 and up
Selecting an aftermarket cat-back exhaust system can be daunting due to the multitude of options available. CORSA Performance Cat-Back Exhausts simplifies this choice by focusing on delivering precisely what you desire to enhance your driving experience. *Aggressive Performance Sound* Our systems are meticulously engineered to match the specific make, model, and harmonics of your vehicle, providing an acoustically styled exhaust note that reflects both the car and its owner's personality. *No Drone* Our RSC™ technology sets us apart by eliminating "problem" frequencies that cause interior drone or resonance at cruising speeds. With CORSA, you can enjoy your car's sound at idle, during acceleration, and while cruising without any unwanted noise. *Improved Horsepower And Torque* Our patented non-restrictive Straight-through design reduces back pressure, unlocking additional power and torque for enhanced performance. *Potential For Better Fuel Economy* Reduced back pressure and increased power lead to improved engine efficiency, potentially resulting in better fuel economy. *Premium 304L Stainless Steel Construction* Constructed from premium 304L stainless steel and devoid of cheap, easily degraded packing materials, our exhaust systems are built to last. *Limited Lifetime Warranty* Backed by our Limited Lifetime Warranty, you can trust that our exhaust systems will endure for years to come. *Includes All Necessary Hardware And Full Color Instructions* Our systems include high-quality TORCA Clamps made from 304SS, along with detailed instructions featuring full-color photos for a straightforward installation process. *50 State Emissions Legal* Designed to install rearward of the factory catalytic converter, our systems ensure compliance with emissions regulations across all 50 states. *Handcrafted In The USA* Each system is proudly handcrafted in Berea, OH, USA, reflecting our commitment to quality craftsmanship and American manufacturing.
Show More Show Less

Magnaflow - Corporate Logo
T#:373508
Part#: 16533
Ships in 1 Business Day
$ 1,424.00 USD
$ 1,424.00 USD

Protect your BMW's exhaust system from the corrosive effects of road salt and moisture with the Magnaflow Performance Exhaust System. Over time, stock exhaust units can rust and break, leading to excessive noise and vibrations. Upgrading to a Magnaflow system not only resolves these issues but also unleashes hidden power by improving engine airflow.

  • Rust Protection: Constructed from 100% stainless steel, the Magnaflow system resists rust and corrosion.
  • Performance Enhancement: Dyno tested and proven to increase power by allowing better engine breathing.
  • Quality Construction: Mandrel bent and fully welded for durability and trouble-free installation.
  • Enhanced Sound: Features a 5x8x14" polished muffler for a smooth deep tone, complemented by dual 3" double rolled edge tips.
  • Easy Installation: Designed for a straightforward installation using stock hanger positions and mounting points.
  • Complete Kit: Includes clamps, hangers, and detailed instructions for a comprehensive exhaust upgrade.

Upgrade your BMW's exhaust system with the Magnaflow Performance Exhaust, ensuring longevity, improved performance, and a distinctive deep tone.

Show More Show Less
Magnaflow - Corporate Logo
T#:189206
Part#: 16537-M
Ships in 1 Business Day
$ 1,424.00 USD
$ 1,424.00 USD
Magnaflow 2011 BMW 328I L6 3.0L Dual Rear Exit

AWE - Corporate Logo
T#:589627
Part#: GRP-EXH-BMF8X34N
Ships in 4 Business Days
Starting at $ 2,045.00 USD
Free Shipping
Starting at $ 2,045.00 USD
Free Shipping
AWE has one vision: To unlock performance. AWE has a unique facility where every step, from design to production, is completed within their facilities. This results in state-of-the-art exhausts with unparalleled quality control and top tier performance. The Track Edition Exhaust for your F8x BMW is the most aggressive exhaust offered from AWE. This exhaust delivers an unobstructed sound from your S55 motor, that is sure to turn heads. Choose from multiple tip sizes in Diamond Black finishes available in 90mm or 102mm. Other features include: Available as Resonated and Non-Resonated Clean, non-raspy S55 tone Precision-engineered integrated X-pipe Full dual 3” CNC mandrel-bent configuration 29lb weight saving over stock Max gains of 20 hp and 31ft-lbs of torque at the crank Less is more: clean, non-baffled, straight-through design maximizes performance Handcrafted from U.S.-sourced CNC mandrel-bent .065” wall T304L stainless steel Proudly engineered, designed, and manufactured in-house at AWE Direct bolt-on system for factory-like simplicity No Check Engine Light - Guaranteed Perfect Fitment - Guaranteed Featuring the AWE Lifetime Exhaust Warranty
Show More Show Less

Milltek Sport - Corporate Logo
T#:380498
Part#: SSXBM462
Back Ordered
$ 2,387.99 USD
Free Shipping
$ 2,387.99 USD
Free Shipping
With in-house production and engineering in the United Kingdom, they have been designing and developing exhaust systems for over 32 years. This experience has helped put Milltek on the map when it comes to performance exhausts, with offerings that range from Audi/Volkswagen to Porsche, BMW, and even Bentley. But, they don't stop there. Milltek has also made its presence felt in the motorsport community. Through partnerships with various race teams throughout the world, Milltek has gathered feedback on ways to improve their systems from enthusiasts at every level. Constructed of type-304 aircraft grade stainless steel, the quality is top-notch. To take it a step further, Milltek offers a lifetime warranty to the original purchaser.
Show More Show Less
Dinan G87 M2 Foundation Package
Call In Or Chat For Best Price!
Dinan - Corporate Logo
T#:34919035
Part#: G87-M2-F-GBKT
Ships in 2 Business Days
$ 5,099.99 USD
$ 5,099.99 USD
Foundation packages represent the most direct path to increased power while retaining drivability and safety. The combination of Dinan modifications work harmoniously with one another and offer a balanced blend of enhanced engine efficiency, improved acceleration and increased power to go along with a tasteful high performance look and unmistakable Dinan sound. Whether you start with the base Foundation package that includes the core hardware building blocks (intake and exhaust), or opt for packages that further enhance your vehicles power output and abilities you will be well on your way to an elevated experience. WHY GET A PACKAGE? We understand the building a modified car in stages is often preferred for various reasons. Not knowing how deep into the modification journey you may go or simply for financial reasons are common justifications for a measured approach. However, often when building in stages, parts are mixed and matched that were not designed to interact with one another which can lead to sub-par results and unhappiness with a vehicle you should be enjoying. By purchasing and installing popular curated packages of parts that were all designed to work with one another you bypass these common faults and receive a complete solution you can enjoy to the fullest from day one. As a bonus, a 10% discount is applied to package purchases compared to buying the same components a la carte. WHAT'S INCLUDED IN THE BASE G87 M2 FOUNDATION PACKAGE (F)? Dinan Carbon Fiber Cold Air Intake (D760-0063) for increased flow, efficiency as well as underhood visual appeal Dinan Free Flow Axle-Back Exhaust w/ Black Tips (D660-0100-BLK) and corresponding X-Pipe (D660-0101) for maximum aural pleasure Features: Maximum gains of +6 HP and +5 lb-ft of torque (Exhaust) Smoother, louder and sportier sound (Exhaust + X-Pipe) Computer controlled exhaust valves are retained and limit noise during low-speed driving and open fully during high-load conditions (Exhaust) Deletes resonators between the secondary catalysts and rear muffler for increased volume (X-Pipe) 11-pounds lighter than the stock (Stock: 66-pounds vs. Dinan: 55-pounds) (Exhaust + X-Pipe) Reduced intake restriction for Increased turbo efficiency with greater power potential on modified builds (Intake) More robust and aggressive induction soundtrack (Intake) Improved throttle response (Intake) 7 points towards the illustrious Dinan deck lid badge
Show More Show Less
Active Autowerke - Corporate Logo
T#:2393398
Part#: 11-051B
Ships in 3 Business Days
$ 3,820.00 USD
Free Shipping
$ 3,820.00 USD
Free Shipping
Active Autowerke is proud to announce the release of their Signature M2 Competition Exhaust System. This system is the result of countless hours of R&D to obtain the perfect combination of performance and sound. Constructed of 100% 304 TIG welded stainless steel, they have created a modular exhaust system that will provide enough flow to support power levels way above the stock M2 Competition. When installed as a complete unit, the exhaust diameter of our system never shrinks below 3.5” The rear section splits from a single 3.5” pipe in to dual 3.5” pipes; one of which is valved and leads straight to the exhaust tips with the other leading to a straight through muffler that reduces noise levels when the valve is closed. The Y-pipe is hand built to maintain maximum exhaust velocity throughout the entire system. With the reduced back pressure and large single-pipe design you can expect exhaust velocity to remain as high as possible throughout the entire system. The design is also capable of handling much higher power levels than stock. It’s over engineered to have no issues handling the increased exhaust volume from extensive modifications including turbo upgrades. The stock M2 Competition sounds great, but there’s always room for improvement! They configured 7 different muffler and resonator setups before settling on the final product. With the valve closed the system is slightly louder than stock but with a great note. With the valve open it’s significantly louder but without the metallic, hollow sound of a full straight pipe exhaust. MADE IN THE USA FEATURES: Mandrel bent 304-stainless construction Completely TIG Welded (No MIG Welding at all) Flow efficient Y-Pipe design Perfect fitment with adjustable 90mm double walled tips True 3.5” turbo back design Uses OEM valve motor Designed to be used at stock power levels along with highly modified engines No permanent modifications required Manufactured in house in Miami, FL.
Show More Show Less


Milltek Sport - Corporate Logo
T#:593627
Part#: SSXBM1072
Ships in 3 Business Days
$ 1,845.99 USD
$ 1,845.99 USD
With in-house production and engineering in the United Kingdom, they have been designing and developing exhaust systems for over 32 years. This experience has helped put Milltek on the map when it comes to performance exhausts, with offerings that range from Audi/Volkswagen to Porsche, BMW, and even Bentley. But, they don't stop there. Milltek has also made its presence felt in the motorsport community. Through partnerships with various race teams throughout the world, Milltek has gathered feedback on ways to improve their systems from enthusiasts at every level. Constructed of type-304 aircraft grade stainless steel, the quality is top-notch. To take it a step further, Milltek offers a lifetime warranty to the original purchaser.
Show More Show Less
Armytrix - Corporate Logo
T#:582660
Part#: BMF13-QS17M
Ships on Sep 24, 2026
$ 4,676.00 USD
Free Shipping
$ 4,676.00 USD
Free Shipping

To harvest the full potential of the BMW engine, Armytrix utilizes quality T304 stainless steel, forged with the most advanced technologies and by the highest standard, to build their valvetronic exhaust. Meticulously engineered, the system handles an increased volume with ruthless efficiency. The refinement and amplification of power and sound alter the entire identity of the vehicle. Upgrades to HP and torque provide more freedom than ever and the auditory sensation throughout the rev range will have your adrenaline pumping to the beat of the car.

The ARMYTRIX exclusive OBDII dongle system reduces the installation time by 50%! With clear displays and user-friendly controls, navigate through our smartphone app to attain an insightful look into the vehicle's real-time operational status and complete control over the valve settings. They have tailored each exhaust for carrying the maximum payload to be delivered to thunderous effect. Their streamlined system is lighter, ridded of the OE deadweight and offers an unrestrictive flow; the improved efficiency plays a vital role in the dramatic improvements in both horsepower and torque.

ARMYTRIX Corp. has established itself as a manufacturer of world class titanium and stainless valvetronic exhaust systems for high-end performance cars. The ARMYTRIX R&D team consists of highly trained and experienced German and Japanese factory engineers and supercar tuning experts, each having decades of knowledge and experience within the race track and automotive performance industries.

Includes:

Front Pipe 1 & 2
Mid Y Pipe
Valvetronic Mufflers
Wireless Remote Control Kits
Quad Matte Black Tips 4X89mm
Features:

Power ( HP): 16
Torque ( Nm): 22
Weight Saving (-Kg):5.7
Reduction of Installation Time by 50% compared to traditional cable wires
Comprehensive Selectable Options
Real time Update of Selected Categories
Quick & Accurate Data Logging
App Controlled Valve System via OBDII Port
View Install Instructions Here.
Fitment:

BMW 535i F10 11-19

Show More Show Less