Schwaben for BMW Z4 M Roadster S54 (2003-2008)

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Schwaben Oil Filter Removal Pliers / Wrench are designed to tackle the most stubborn spin-on filters with ease. Featuring large, adjustable jaws with raised teeth, these pliers provide a secure grip on a wide range of filter diameters. The long, plastic-coated handles offer a comfortable grip and added leverage, making filter removal straightforward and efficient.

• Efficient Removal: Handles the toughest oil filters with ease, thanks to its robust design.
• Versatile Fit: Adjustable jaws with raised teeth ensure a secure grip on various filter sizes.
• Comfortable Use: Long, plastic-coated handles provide a comfortable grip and extra leverage.
• Durable Construction: Built to last, ensuring reliable performance for frequent use.

Warning: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. For more information, visit Proposition 65.

Having a nice quality set of extensions always comes in handy when working on BMW's. With the slanted position of most engines and the tight engine bay, there almost always a hole for the extension to reach into and easily remove the fastener.

Features:

• 3/8" drive extension set features high quality tool steel with an easy to wipe clean satin finish
• Knurled section on shaft allows for easy turning by hand when needed
• Size range - 1.5",3",6",10" with a convenient storage tray

A professional quality flex ratchet features a fine satin finish designed for durability and easy clean up.

Features:

• Special designed 72T gear mechanism
• 5 degree of handle movement between gears 
• Flex head has 7 detent positions in a 180 degree swing
• Push button release holds socket tight until you are ready to release
• Ratchet is a full 290mm ( 11") long for extra leverage.

Limited Lifetime Warranty

It only takes a gust of wind to have your hood crashing down on your head, or if you have a carbon fiber hood and no longer have the gas struts than this could be what you need.

 This hood prop is adjustable, lightweight, and sturdy making it easy to keep out of the way in the trunk so it's there whenever you need it. 

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

Quality combination wrenches are a must when doing any kind of automotive work.

Features:

• A complete set from 8 to 19 mm 
• Professional quality wrenches in full length feature open end on one end and 12 pt box on the other
• Satin finish provides superior feel, slip resistant grip, easy cleanup and inhibits rust
• Includes sturdy wrench holder for easy storage
• Limited Lifetime Warranty

Provides access to recessed areas with extra long bolts, as found on some bumpers, rear lamps, diesel glow plugs (10mm, 12mm, 17mm), spark plugs, and door hinge fittings.

Areas where this tool set is helpful includes a range of specific applications such as BMW N54 Twin-turbo valve cover bolts (12mm), BMW E90/92 Lug Nuts (17mm), BMW Spark Plugs (14mm), BMW E90/92 Clutch Bleeder Valve (11mm), and other common Euro applications.

Kit includes: 

• 1/4" adapter
• 8mm
• 9mm
• 10mm
• 11mm
• 12mm
• 13mm
• 14mm
• 15mm
• 16mm
• 17mm
• 18mm

​This Schwaben floor jack is loaded with design details that make this floor jack one of the best jacks on the market. Here are some of the details.

Dual pump pistons raises the saddle to maximum height in only 5 pump strokes, with minimum effort.
Special low profile thick frame side plates and reinforced lift arm for added strength and use.
Wide track front wheels help provide chassis torsion control and durability.
Angular positioned pump pistons provide maximum effective pump stroke even when jack is completely under the vehicle.
Ball bearing mounted rear swivel caster wheels for easy maneuverability.
Side mounted handles for carrying and easy positioning.
Overload and bypass safety valve prevents jack overload and over extension.