Control Arm Bushings

Swapping in E46 control arms into your E30 or E36 will significantly increase negative camber by widening the track width and will also give you more clearance for more steering angle. Condor's conversion bushings are machined from UHMW due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change). They've designed them offset to re-center the wheel and give your e30/e36 the correct caster. They will include a stainless-steel insert that tightly presses over the hex pattern on the E46 control arms. You do not need to grind down your control arms or make any other modifications to your chassis. Please note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36.

Fitment:
Fits the following Meyle and Lemforder arms with 21-22MM Hex.

LEMFORDER ZHP - 31122282121 & 31122282122
LEMFORDER - 31126777851 & 31126777852
MEYLE HD - 31126777851 & 31126777852
*Please note that Meyle makes a standard e46 control arm and a Heavy Duty control arm. SOME HD arms have a hex that is larger in size. These HD control arms may need to be shaved 1-2 mm for proper fitment.

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Front Control Arm Rear Bushings With Brackets BMW E46 Z4 provide a significant upgrade for BMW E46 and Z4 E85 & E86 owners seeking enhanced performance and handling. Designed by Turner Motorsport, these high-quality bushings optimize control and road-handling capabilities to elevate your driving experience.

• Improved Handling and Stability: Enhances the already impressive handling of BMW E46 and Z4 models by reducing sway and body roll during cornering, ensuring stability and responsiveness in tight turns.
• Enhanced Cornering Performance: Increases rigidity for more precise and controlled cornering, providing better grip and control whether on winding roads or racetracks.
• Mitigation of Understeer: Addresses understeer by redistributing load more evenly between front and rear tires, improving balance and control.
• Durability and Longevity: Constructed from high-quality materials for extended service life, these bushings endure daily driving and spirited performance while reducing wear on suspension components.
• OE / OEM Cross Reference Numbers: 31126757623

This is a replacement Front Upper Control Arm Bushing also known as the "tension strut bushing" or "thrust arm bushing" for 2004-2010 BMW E60 5 series models (non Xi models). One required per arm. 

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i M5 - sorry not for Xi models
2004+ E63 BMW 645ci 650i M6

Looking to get into drifting but dont know where to start? Our tubular control arms are designed in-house to be a longer, stronger, and lighter weight upgrade that provides the track width and adjustability to start your drift setup.

Our drift kit provides +65mm more track width (per side) than stock. Wider track width reduces the amount of load transfer to the outside when cornering, increases cornering power, and allows more inner clearance for meaty wheel and tire setups or brake ducts. Correct your suspension geometry, and increase your steering response and handling characteristics. Provides +65mm more track width (per side) than stock! Includes FCAB's with upgraded monoball bushings to push your E46 to the next level.

Design Features and Benefits:

4130 chromoly construction
Fully TIG welded design
OE style inner ball joint
FK spherical outer joint
Includes sway bar tab
Powder Coated finish
To be used without roll center correction

Performance:

Drift control arms provide 65mm increased track width per side compared to stock
(432mm from ball joint to ball joint)
More clearance inboard for tire/wheel/brake ducts

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver. 

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

This part fits the following BMWs:
1996 - 2004 E39 Sedan 525i 528i 530i 540i 

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Suspension bushing wear over time and make your car less responsive and controllable and the ride quality drop. It is recommended to replace suspension bushing every 50 to 60 thousand miles for the best handling and driving experience possible.

This item fits the following BMW Chassis:
F22,F30,F31,F32,F33,F34,F36

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,F15,F16