Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap. This spring set is two front coil springs and two rear ride height sensor rods.

Dinan spring specs -

• F: -5/8" (16mm)
  
• R: -3/4" (19mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2016+ F85 BMW2016+ F86 BMW

Control arms are some of the most crucial components on a BMW suspension. The control arms literally control the wheel and suspension as they go through their range of motions. A faulty or worn control arm or ball joint is a very dangerous and potentially life-threatening problem so make sure they are inspected and replaced at regular intervals. For a street-driven car we advise yearly inspection and a full replacement every 3-4 years. For track-driven cars these should be inspected before every event and replaced every two years.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Genuine BMW Control Arm With Rubber Bushing, Left
This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,F15,F16

Ball joints begin to pop and rattle after a long period of wear and tear. An OEM Lemforder ball joint is the perfect replacement to ensure complete reliability eliminate any noises from the suspension.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,F15,F16

Correct toe settings contribute to both stable steering and even tire wear. The SPC Performance wheel toe bar tool is designed to prevent vehicle drifting and ensure uniform tire wear. It includes a steel bar equipped with sliding adjusters and pointers to accurately assess the vehicle's toe alignment.

For wider wheel bases use T#386442!

If you're refreshing your struts and springs this tool is a must, properly compress the springs, easily remove and install the strut nut, and smoothly remove the spindles.

Features:

• Spring Compressor
• Strut Nut Sockets
• Spindle Spreader

The Schwaben Pitman arm and tie rod puller offers a blend of slim construction and sturdy resilience, making it exceptionally suited for accessing tight spaces while also possessing the strength to manage high torque pulls across a diverse array of cars and light trucks. Fashioned with a heat-treated pulling screw, it is fortified with a protective black finish to resist rust and corrosion, guaranteeing enduring durability. Its sleek profile facilitates easy navigation through confined areas, complemented by meticulously crafted machined threads that ensure seamless operation. Compatible with a 3/8-inch drive, this tool proves to be a versatile asset for a multitude of automotive tasks.

Features:

• 3/8-inch Drive
• Smooth machined threading
• Slim design to fit into tight spaces

Schwaben Shock Nut Socket - 16mm

The Schwaben Shock Nut Socket - 16mm is an essential tool for securely mounting shocks to their mounts. Designed to help achieve the correct torque specification, this socket allows the use of an internal hex wrench to hold the damper shaft in place while using a torque wrench to apply the correct torque. Properly torquing the retaining nut is crucial to prevent premature mount failure or loosening. This high-quality socket ensures a precise fit and reliable performance for maintaining your vehicle's suspension system.

Benefits:

• Allows accurate torquing of shock retaining nuts to prevent mount failure
• Designed for use with an internal hex wrench to secure the damper shaft
• Ensures proper torque application with your torque wrench
• Helps avoid premature mount failure and nut loosening
• High-quality construction for durable and reliable performance
• Compatible with 16mm shock nuts

Collar Nut | Self-Locking is a vital component used in various suspension locations on BMW and MINI vehicles. This 8mm hex nut provides reliable performance and secure fastening for suspension systems.

• Self-Locking Feature: Ensures that the nut remains securely fastened under vibration and stress.
• Durable Construction: Designed to withstand the demands of automotive suspension systems.
• Versatile Use: Suitable for various locations in the suspension system of BMW and MINI vehicles.
• Precision Fit: 8mm hex size for accurate and easy installation.