Packaged by Turner for BMW 3 Series E90 (2006-2011)

The water pumps in these BMW models are known for failure near 80,000 miles is a very common issue often times leaving the owner stranded. This kit provides a single stop for water pump and thermostat replacement needs to save the search and get you back on the road.

Kit includes:

• OEM Wahler Thermostat
• OEM VDO Electric Water Pump
• Genuine BMW Antifreeze/Coolant
• OEM VDO Mounting hardware required for both the thermostat and water pump

Enhance your BMW's performance upgrades with this comprehensive installation kit designed for cup kits or coilovers. This kit provides all essential components necessary to facilitate the installation process, ensuring a hassle-free setup for your vehicle modification.

Key Benefits:

• Ideal for installing cup kits or coilovers on your BMW
• Comprehensive kit includes all necessary installation components
• Facilitates a hassle-free setup for vehicle modifications

Replacing your struts and shocks? Don't forget the bushings! The rubber mounts for the shocks will go bad over time, especially if you drive hard or the roads are particularly rough. The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install. When installing new shocks, that is the perfect time to also replace the mounts. There is no additional time to install them, no special tools required, and doesn't take any extra time! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs. 

This item fits the following BMWs: 
2006-2012 E9X BMW All xi models - 325xi 328xi 330xi 335xi

Turner Motorsport has made it easier than ever to get the high-quality upgrade components you need for your next brake service—all in a single, convenient kit. Our performance brake service kit includes premium ECS rotors, ECS EP24 "Enthusiast Performance pads, a wear sensor, assembly grease, and a full set of rotor set screws, ensuring a seamless upgrade process. Expertly assembled for perfect compatibility, this kit is designed to keep your braking system performing at its best.

Kit Includes:

ECS 2-Piece Semi-Floating Cross-Drilled & Slotted Rotors (Rear) Rear ECS EP24 "Enthusiast Performance" Brake Pads Brake Pad Wear Sensor ECS Stainless Steel Rotor Set Screws AGS Brake Lubricant Compound Packet Upgrade your braking performance with precision-engineered components!

Turner Motorsport has made it easier than ever to get the high-quality upgrade components you need for your next brake service—all in a single, convenient kit. Our performance brake service kit includes premium ECS rotors, ECS EP24 "Enthusiast Performance pads, a wear sensor, assembly grease, and a full set of rotor set screws, ensuring a seamless upgrade process. Expertly assembled for perfect compatibility, this kit is designed to keep your braking system performing at its best.

Kit Includes:

ECS V5 Cross-Drilled & Slotted Rotors (Rear) Rear ECS EP24 "Enthusiast Performance" Brake Pads Brake Pad Wear Sensor ECS Stainless Steel Rotor Set Screws AGS Brake Lubricant Compound Packet Upgrade your braking performance with precision-engineered components!

2006 E90 330i Stage 1 Performance Package
Peak Power Gain: +29hp / +29ft-lbs
Rev limit: 7000
Octane: 91 or higher

Our Stage 1 kit featuring a cold-air intake kit and matching performance software. The aFe intake is a cone filter with a heat-blocking shield around it. The larger surface area of the filter, combined with the heat shield, allow more cool air to enter the engine - creating more power and torque, a richer engine sound, and better throttle response. The kit is supplied complete with heat shield, intake tube, sealing materials, hardware, and install instructions.

Our flash software is tuned especially for a cold-air intake, maximizing the potential and providing smoother power delivery. We take the stock software and make adjustments for 91 octane (stock software is set around 87). We can get more power and torque, and increase fuel efficiency without affecting driveability or the life of the engine. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

Our software fully maximizes the 'high-output' N52B30O0 engine in the 330i. Our software has been carefully developed on the dyno and the road to provide optimal power and torque gains at all RPM. We change the fuel, Valvetronic, and VANOS maps as well as revise the factory torque limiters. We have paid particular attention to increasing low and mid-range torque. The stock BMW software is hampered by settings for 87 octane fuel. By re-mapping the engine programming for 91 octane, we can make more power, torque, and improve fuel mileage - all without harm to the engine or affecting driveability. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

There are two ways to install our software: mailing the ECU to us for a reflash or do-it-yourself install with our Turner Flash tool:

Mail-In Reflash - lower upfront cost but additional shipping charges. Minimum downtime of at least three days. We have a 24 hour turnaround on shipping the ECU back to you but factor in transit time. Expert installation of your software at our facility.
Turner Flash DIY tool - higher upfront cost but files are emailed back and forth. No downtime - you can still drive the car while we process your tune. Files are emailed back and forth - your stock file comes to us, a tuned file is returned to you. Easy install via Windows laptop. 

E90 330i Stage 1 Engine Upgrade includes:
aFe Cold Air Intake (filter, heat shield, intake tube)
Turner Motorsport Performance Software Flash

This item fits the following BMWs:
2006 E90 BMW 330i

2006 E90 325i Stage 1 Performance Package
Peak Power Gain: +29hp / +29ft-lbs
Rev limit: 7000
Octane: 91 or higher

Our Stage 1 kit featuring a cold-air intake kit and matching performance software. The aFe intake is a cone filter with a heat-blocking shield around it. The larger surface area of the filter, combined with the heat shield, allow more cool air to enter the engine - creating more power and torque, a richer engine sound, and better throttle response. The kit is supplied complete with heat shield, intake tube, sealing materials, hardware, and install instructions.

Our flash software is tuned especially for a cold-air intake, maximizing the potential and providing smoother power delivery. We take the stock software and make adjustments for 91 octane (stock software is set around 87). We can get more power and torque, and increase fuel efficiency without affecting driveability or the life of the engine. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

Our software fully maximizes the 'low-output' N52B30 engine in the 325i. Our software has been carefully developed on the dyno and the road to provide optimal power and torque gains at all RPM. We change the fuel, Valvetronic, and VANOS maps as well as revise the factory torque limiters. We have paid particular attention to increasing low and mid-range torque. The stock BMW software is hampered by settings for 87 octane fuel. By re-mapping the engine programming for 91 octane, we can make more power, torque, and improve fuel mileage - all without harm to the engine or affecting driveability. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

There are two ways to install our software: mailing the ECU to us for a reflash or do-it-yourself install with our Turner Flash tool:

Mail-In Reflash - lower upfront cost but additional shipping charges. Minimum downtime of at least three days. We have a 24 hour turnaround on shipping the ECU back to you but factor in transit time. Expert installation of your software at our facility.
Turner Flash DIY tool - higher upfront cost but files are emailed back and forth. No downtime - you can still drive the car while we process your tune. Files are emailed back and forth - your stock file comes to us, a tuned file is returned to you. Easy install via Windows laptop. 

E90 325i Stage 1 Engine Upgrade includes:
aFe Cold Air Intake (filter, heat shield, intake tube)
Turner Motorsport Performance Software Flash

This item fits the following BMWs:
2006 E90 BMW 325i