Turner Motorsport for BMW 5 Series E60 (2004-2010)

All vehicles will lose some degree of performance due to heat soak under the right operating conditions.  Engine management systems constantly monitor operating conditions and modifying parameters based on sensor inputs. BMW integrated the intake air temp sensor in the MAF housing on models such as the E39 M5, and, being sandwiched behind a hot radiator and in some applications next to an even hotter valve cover, this is less than ideal for performance applications. Absorbing excess heat from its surroundings, the MAF can’t shed it fast enough, and the ECU reads an inaccurately high intake air temperature. Compensating for this false hot air measurement, the ECU pulls timing and runs a richer fuel mixture, resulting in a significant loss of torque.

What can you do?  Locate an intake air temp sensor in a location where it can properly measure incoming air temps and where it's less prone to heat soak. Mounting the sensor further away from the heat source and isolating it from the MAF housing, it can both resist the effects of heat soak longer and respond to temperature changes more quickly.  The result is you’ll experience reduced torque loss and more consistent power output when you’re pushing your engine hard. 

The Turner engineering team was initially skeptical of the claimed performance benefits of this modification. They first set out validate the functionality and performance benefit of a temp sensor relocation. Replicating stop-and-go traffic heat soak in a 2001 540i was a simple task in a controlled environment - their dynometer. First the car was heat soaked to simulate being stuck in traffic or moving at low speeds by running the car four times on the dyno with the dyno's cooling fans disabled. The fans were then turned on for three more runs to observe the recovery rate once air flow was reintroduced. The test: following this procedure once with a stock IAT, and once with their relocation kit in place. 

The result? Turner recovered 11lb-ft torque at 2500rpm through use of their relocation kit, with even greater recovery to be found for M5 owners. Here are the heat soak-related torque losses Turner experienced:

Stock IAT location:
18rwtq at 2500rpm
10rwtq at 3000rpm
9rwtq at 3700rpm

Turner IAT Relocation:
7rwtq at 2500rpm
5rwtq at 3000rpm
5rwtq at 3700rpm

**Click here for installation instructions**

The Turner engineering team designed a complete plug and play kit (unlike all other options on the market) that makes for quick, easy, and reversible installation. Weather-sealed connectors keep out the elements, while sheathed wiring offers a clean appearance underhood. With a harness nearly 3 feet long - the Turner IAT relocation kit offers flexibility in positioning, but not too long that you're left with unsightly excess wiring. Turner recommends positioning the sensor in a location away from engine heat, but still within the intake ducting to achieve accurate intake temp readings - such as the far side of the base of the airbox. Vehicles with cold air intakes with cone-style filters can even position the sensor in the end of the filter. Simply drill a hole in your (cool) location of choice and plug in the harness. More information including installation instructions and some good examples of sensor mounting locations can be found in our DIY PDF. 

We include everything you need to relocate your IAT, just select your desired sensor brand below - Genuine BMW or original equipment Beru.

Also the perfect plug-n-play option for anyone looking to upgrade their intake to utilize an Alpha-N tune!

Note for vehicles with M62 engine: applicable to 1999 and up

Get MORE HORSEPOWER and TORQUE on your 2006 and newer M5 sedan or M6 coupe/convertible by replacing the stock crank pulley with this specially designed performance version. The Power Pulley reduces rotational mass and safely under drives your belt driven auxiliaries for reduced parasitic power loss. The end result: More power to your M5 or M6's rear wheels! Designed to give the best performance benefit with no sacrifices or compromises to your BMW's reliability. These have been tested on hundreds of cars before public release and there are simply NO DOWNSIDES to this upgrade.

Limited time introductory offer: FREE GROUND shipping on all orders shipped within the 48 contiguous states shipping on this V10 pulley kit.

CNC machined using aircraft grade 6061 aluminum billet, and anodized with a stealthy black coating. Others may advertise "their" crank pulley boasting higher numbers (using a smaller pulley profile), but we have concluded that for street and track driven M5 and M6, this is the best size and design to ensure proper engine temp and auxiliary functionality. As the S85 V10 engine doesn't use a traditional harmonic balancer, all factory harmonics and dampening are fully and properly retained. We've found this pulley alone adds 18 to 22 HP and 17 to 21 Ft/lbs Torque on a stock M5 or M6 with no other mods(!!).

The E60 M5 / E63 M6 Power Pulley Kit includes:
(1) Underdrive Crank Pulley
(1) Correctly Sized Drive Belt
(6) Allen Head Bolts
(1) Installation instructions

This underdrive pulley fits the following BMWs:
2006-2010 E60 M5 sedan
2006-2010 E63/E64 M6 coupe & convertible
 

Upgrade your engine build with Turner's WPC-treated Race Series Bearings, engineered for serious performance enthusiasts. Starting with ACL’s high-performance bearing shells, these Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Key Features:

Duraglide Tri-Metal Construction: ACL's Race Series bearings feature a high-strength overlay for enhanced performance. Optimized Oiling: Designed to promote better oil flow during high-RPM conditions. Precise Fitment: Manufactured with OEM-level precision using micron tolerance machining. WPC-Treated for Strength: Surface treatment adds strength and reduces friction for improved engine performance. No Flash Plating: Allows for better heat transfer and bearing retention. Thermal Discharge Process: Smoother, stronger components through WPC’s unique thermal discharge technology. Enhanced Heat and Friction Resistance: Built to combat the biggest enemies of high-performance engines. Don’t settle for standard bearings—choose Turner Motorsport WPC-treated Race Series Bearings for the ultimate engine performance upgrade. Perfect for your next engine rebuild or rod bearing service!

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

3.0" Inner Diameter
4.0" Outer Diameter
Black Chrome Finish
Double Wall Construction
Straight Cut Style
Includes Stainless Steel Clamp

Universal 2.5" inlet to 3.5" outlet exhaust tip. Priced per exhaust tip.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Mirror Chrome Finish
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

Set of 2 universal 2.5" inlet to 3.5" outlet exhaust tips.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Brushed Aluminum Finish
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

High Performance air filter, replacement filter for Turner Motorsport intakes, or great for your custom intake project. 

Filter Dimension 

• 178MM length 
• 127MM base
• 75MM inlet 

Engineered in-house, we designed this lightweight, single-mass flywheel to provide more than 10 pounds of weight savings over the factory flywheel. While some ultra-lightweight performance flywheels are manufactured from aluminum, our designers opted for a more driveable experience with steel. The mass provided by steel helps dampen vibrations and noise, delivering near-factory refinement with most of the benefits of a lightweight flywheel: quicker throttle response, improved durability (and longevity), and more effective transfer of power to the wheels.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

When it comes to selecting a clutch to pair with a lightweight flywheel, consider the driving you’ll be doing. As a single mass flywheel eliminates the dual-mass dampening of the factory flywheel, to retain the lowest noise, lowest harshness driving experience possible, select a clutch with a dampened disc such as the ACT Heavy Duty. For dedicated track cars, a solid clutch hub is appropriate.

Our recommendations:

Street: ACT Heavy Duty
Track: ACT Xtreme for high torque cars or OE 335is LuK (with 440lbs-ft or less)
Features:

Precision machined from 4140 HT heat treated chromoly steel for exceptional toughness, even wear properties, and durability.
Material quality promotes even wear across the entire friction surface
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability and elevated temperatures
Hardness improves wear characteristics
Black oxide coated for corrosion resistance on non-friction surfaces.
8620 steel pilot bearing pin, case hardened and Precision ground for maximum wear resistance.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 tested and certified to ensure safe operation under extreme operating conditions
SFI 1.1 specifies minimum material properties and requires a 3rd party lab certification test, spinning the flywheel to 1.5x redline for 1 hour to ensure the flywheel will not burst.
Specifically designed to work with N54 architecture clutches
Step height designed to optimize clamp load and maximize the usable range of clutch wear for a long service life
Performance:

Turner Flywheel 18.6 lbs
10 lbs lighter than the factory BMW flywheel (Stock Flywheel 28.9 lbs)
Faster revs
Improved throttle response
Improved acceleration
Sportier driving experience
Stock flywheel weight - 28.9lbs
Turner single mass flywheel weight = 18.55lbs

Single Mass Flywheel Conversion:

Audible chatter from the transmission after installation is considered normal. As with most single mass flywheels, there is less dampening in the flywheel to reduce "gear noise." This chatter noise may be more present when the transmission fluid temperatures are hotter and may be intensified by other modifications. Most gearboxes will experience some chatter noise at hotter temperatures. Please be advised that this noise will disappear once the clutch pedal is depressed. This symptom may be lessened by adjusting transmission fluid weight, turning off electrical/driveline consumers (A/C, High Beams, ETC.), and by raising the RPM slightly.

Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

This item fits the following BMWs with 8 bolt flywheel and build date up to 01/2009 or earlier:
2008-01/2009 E82 BMW 135i 135is 1M
2007-01/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-01/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-01/2009 E93 BMW 335i - Convertible
2008-01/2009 E60 BMW 535i 535xi 535i xDrive

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

3.0" Inner Diameter
4.0" Outer Diameter
Brushed Finish
Double Wall Construction
Slant Cut Style
Includes Stainless Steel Clamp