This braided stainless steel line replaces the stock hydraulic hose connecting your clutch slave cylinder to the clutch master cylinder. There are several deficiences with rubber, especially as it ages - when new the rubber expands and swells under pressure and the pedal can feel spongy. As rubber ages and is exposed to extreme temperatures the rubber can harden and even shrink (common on brake hoses), which results in a stiff pedal. Rubber clutch lines do not stand up to the stresses of hard use. ECS Exact-Fit stainless reinforced clutch lines provide more confident and dependable shifting by maintaining consistent line pressure, long lasting corrosion resistance, and increased protection from failure. These lines are reinforced with braided stainless steel mesh, affording superior expansion resistance. This resistance to expansion creates a firmer pedal, and a more direct clutch pedal feel. The signature red polymer coating provides additional protection from the elements and abrasion.

This particular stainless steel clutch line fits the following BMWs:
2004-2010 E60/E61 5 Series 
2004-2010 E63/E64 6 Series (manual transmission only, no SMG)
2011-20116 F07/F10 5 Series 
2011-2016 F06/F12/F13 6 Series

T60 head flywheel bolt.

Genuine BMW Isa Screw - M12X1,5X25
This item fits the following BMW Chassis:
E82 1M Coupe,E82,E83 X3,E85 Z4,E86 Z4,E89 Z4,E90,E92,E93,F10,F22,F30,F31,F32,F33,F34,F36,F80 M3,F82 M4,F83

Fits BMW Engines including:
N20,N51,N52,N52N,N54,N54T,N55,S55
 

Luk is our recommended brand for OE quality replacement clutches. This clutch is an upgrade for non 335is/550i/650i models - featuring a heavy duty clutch disc and more holding power, while still retaining stock pedal feel.

Includes:

• Clutch friction disc
• Throwout/release bearing
• Clutch fork lever
• Pressure plate
• Pressure plate bolts

Fits the following BMW chassis: 

E92,E93,F10,F12,F13

Engineered in-house, we designed this lightweight, single-mass flywheel to provide more than 10 pounds of weight savings over the factory flywheel. While some ultra-lightweight performance flywheels are manufactured from aluminum, our designers opted for a more driveable experience with steel. The mass provided by steel helps dampen vibrations and noise, delivering near-factory refinement with most of the benefits of a lightweight flywheel: quicker throttle response, improved durability (and longevity), and more effective transfer of power to the wheels.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

When it comes to selecting a clutch to pair with a lightweight flywheel, consider the driving you’ll be doing. As a single mass flywheel eliminates the dual-mass dampening of the factory flywheel, to retain the lowest noise, lowest harshness driving experience possible, select a clutch with a dampened disc such as the ACT Heavy Duty. For dedicated track cars, a solid clutch hub is appropriate.

Our recommendations:

Street: ACT Heavy Duty
Track: ACT Xtreme for high torque cars or OE 335is LuK (with 440lbs-ft or less)
Features:

Precision machined from 4140 HT heat treated chromoly steel for exceptional toughness, even wear properties, and durability.
Material quality promotes even wear across the entire friction surface
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability and elevated temperatures
Hardness improves wear characteristics
Black oxide coated for corrosion resistance on non-friction surfaces.
8620 steel pilot bearing pin, case hardened and Precision ground for maximum wear resistance.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 tested and certified to ensure safe operation under extreme operating conditions
SFI 1.1 specifies minimum material properties and requires a 3rd party lab certification test, spinning the flywheel to 1.5x redline for 1 hour to ensure the flywheel will not burst.
Specifically designed to work with N54 architecture clutches
Step height designed to optimize clamp load and maximize the usable range of clutch wear for a long service life
Performance:

Turner Flywheel 18.6 lbs
10 lbs lighter than the factory BMW flywheel (Stock Flywheel 28.9 lbs)
Faster revs
Improved throttle response
Improved acceleration
Sportier driving experience
Stock flywheel weight - 28.9lbs
Turner single mass flywheel weight = 18.55lbs

Single Mass Flywheel Conversion:

Audible chatter from the transmission after installation is considered normal. As with most single mass flywheels, there is less dampening in the flywheel to reduce "gear noise." This chatter noise may be more present when the transmission fluid temperatures are hotter and may be intensified by other modifications. Most gearboxes will experience some chatter noise at hotter temperatures. Please be advised that this noise will disappear once the clutch pedal is depressed. This symptom may be lessened by adjusting transmission fluid weight, turning off electrical/driveline consumers (A/C, High Beams, ETC.), and by raising the RPM slightly.

Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

This item fits the following BMWs with 8 bolt flywheel and build date up to 01/2009 or earlier:
2008-01/2009 E82 BMW 135i 135is 1M
2007-01/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-01/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-01/2009 E93 BMW 335i - Convertible
2008-01/2009 E60 BMW 535i 535xi 535i xDrive

Experience longer life and less slippage with this Sachs Performance pressure plate for use with sport/racing clutch discs. This pressure plate offers more clamping power, and is recommended for cars making significantly more hp than stock (forced injection, etc) while using a stock flywheel. This is NOT for use on cars with an aftermarket flywheel (stock flywheel only).

Sachs Performance is the racing and performance oriented selection of high quality parts from Sachs and ZF Engineering. Supplying countless brands with OE parts and offering one of the widest selection of OEM replacement parts, they are known for their exceptionally high quality products. You can purchase these performance parts with confidence, knowing they will resist heavy wear and tear for much longer than most other aftermarket options.