BMW Internal Engine Parts for BMW 5 Series E60 (2004-2010)

Turner Motorsport presents the solution to low oil pressure, increased oil operating temperature, or unusual lifter ticking in your BMW. If your car's sensor triggers a warning light due to pressure issues, it's time to consider the Turner Motorsport Oil Pump replacement. Proper maintenance of the oil pump is crucial for optimal engine function, emphasizing the need for regular oil changes every 3,000 to 5,000 miles. Damaged oil pumps can compromise your vehicle's performance, making replacement essential. When installing a new oil pump, don't forget to replace the oil suction pipe for comprehensive maintenance.

• Improved Oil Pressure: Address low oil pressure concerns for enhanced engine performance.
• Optimized Engine Temperature: Mitigate increased oil operating temperatures for better engine health.
• Reduced Lifter Noise: Eliminate uncommon ticking sounds for a smoother ride.
• Preventive Maintenance: Regular oil changes and pump replacement ensure prolonged engine life.
• Comprehensive Kit: Turner Motorsport recommends replacing the oil suction pipe during the oil pump installation.

Ensure your BMW runs at its best by choosing Turner Motorsport's Oil Pump replacement.

Genuine BMW Bearing Ledge Exhaust
 

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMW Chassis:
E82 1M Coupe,E70 X5 X5,E71 X6,E82,E83 X3,E85 Z4,E86 Z4,E89 Z4,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F32,F33,F34,F36,F80 M3,F82 M4,F83

Fits BMW Engines including:
N51,N52,N52N,N54,N54T,N55,S55
 

Rod bearings should be replaced as a preventative measure before 80,000 miles. This package is the most complete rod bearing overhaul kit available and includes not just the latest BMW rod bearings and connecting rod bolts, but also everything else that should be replaced with the oil pan and front subframe off the car.

Rod bearings continue to be a sore subject among M3, M5, and M6 owners. The rod bearings in the S85 V10 have been known to fail within 60,000 miles. There could be a number of reasons for premature failure with a lot of finger-pointing as to the real cause. Whatever the reason, rod bearings are wearing out sooner than expected and their replacement should be considered a required preventative maintenance item. We suggest a replacement interval of between 60,000-80,000 miles with frequent engine oil analysis done along the way*. Driving moderately and allowing the engine to warm up before hard use will also extend rod bearing life.

After doing so many rod bearing replacements in our own service shop we have put together this comprehensive overhaul package. Our package includes -

Genuine BMW rod bearings
- 11247841703, upper bearings - latest design from BMW (either original or WPC treated**)
- 11247841702, upper bearings - latest design from BMW (either original or WPC treated**)
- 11247834522, connecting rod bolts
- Red Line engine assembly lube

Oil Pan
- 11137836361, oil pan gasket
- 07119905485, oil pan screws (required by BMW)
- 07129905600, oil pan screws (required by BMW)
- 11137836568, oil pan screws
- 07119963129, seal washers
- 11417836233, auxiliary oil pump gaskets
- 11121304174, oil pickup tube o-ring

Replacing the rod bearings requires mechanical knowledge and skill, a clean workspace, and several specialist tools. Our preferred procedure is to leave the engine in the car but remove the front subframe. The engine must be supported from above with an engine brace. Removing the front subframe involves disconnecting the control arms and steering rack and steering column. The oil pan can then be removed and you can access the connecting rods and bearings. Replacing the rod bearings themselves is straightforward but patience and forethought will be extremely helpful. In addition to analyzing the severity of the rod bearing wear, the crankshaft must also be inspected closely for damage. Rod bearings that have been severely worn may have damaged the crankshaft (requiring replacement or machining).

* BMW released an updated rod bearing around 2011 that uses different materials than the original design. The old rod bearings were constructed with several layers or metal, including copper and lead. If an engine oil analysis revealed high levels of these specific metals then it was a sure sign that the rod bearings were nearing replacement. However, the new BMW bearings do not use copper or lead so an oil analysis will not alert you to heavy bearing wear. The new bearings are also a harder material which prolonged the life of the bearing but increased the liklihood of crankshaft damage if a bearing failed. Even though the bearing theoretically lasts longer it's even more important to preventativly replace them before they damage the crankshaft.

** These WPC-treated bearings are the best we have seen for the S85. WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are factory BMW bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

***BE Bearings is another top pick when considering which bearing kit to choose. Working with Clevite, an OE bearing supplier, their design allows for a bit more clearance than stock, allowing better oil circulation and reducing friction. The material is also made from the original bearing composition of lead-copper, not the updated tin-aluminum used in factory BMW bearings which was excessively hard, potentially damaging the crankshaft when high friction occurred. This softer metal composition can also be tested for via oil analysis, allowing you to see high bearing wear, something the tin-aluminum bearings don't give you the ability to do.

Internal VANOS Pressure Line
One of the VANOS oil lines runs along the inside of the timing chain cover and into the oil pan. It can only be replaced with the oil pan removed. If you have sluggish performance or VANOS fault codes this is one of the common causes and now is the perfect time to replace it. If it fails down the line the oil pan will have to be removed again.

Front Subframe Hardware
Our preferred procedure for accessing the engine block is by disconnecting the control arms and steering rack and then removing the front subframe altogether. This hardware is not required but may be a good idea, especially if your original subframe bolts are rusty. Hardware includes:
31106760222, front subframe mounting bolts
31106770256, front subframe mounting bolts
33326760668, front wishbone collar nut

Tie Rod Boots
32106765782, tie rod boot kit

Motor Mounts with Hardware
22116762607, left motor mount
22116762608, right motor mount
07129904088, motor mount bolts
07129904865, motor mount nuts

Engine Oil Change
Liqui Moly GT1 10w-60 engine oil
11427840594, OEM oil filter.

This package fits the following BMWs:
2006-2010 E60 BMW M5
2006-2011 E63 BMW M6

Has your BMW's with the N62 V8 engine developed a coolant leak at the front of the engine from the timing cover weep hole? If so the it is likely that the coolant transfer pipe seal, located below the intake manifold has developed a leak. Normally, replacing the seal on this pipe would require almost 40 hours of labor and involve removing the entire engine from the car, then removing the cylinder heads, and timing covers. With this new collapsible pipe this repair can be accomplished in under 10 hours! This solution will save you or your mechanic from a bunch of headaches and get your V8 back on the road leak free!

With more than 100 years in the industry, Elring is one of the oldest names in the European autoparts segment. Delivering OE-quality you can rest assured the job will be done right the first time. 

video: N62 Cooling Pipe Replacement

Supplement Gasket Kit Parts List

(click to expand)

BMW p/nQtyDescription

115317100481Rear Engine Block O-ring,

115175077171Heat Pipe w O-ring

115175085351Water Pump Gasket

115114399761Valley Pan Pipe Pump

111475072781Valley Pan w Gasket

116175211812Intake Manifold Gasket

071199035962Camshaft Adjuster O-ring

123114399881Alternator Feed Pipe

750il gasket kit deletes 11617521181 and 07119903596 and adds - 8 - 11617537999 profile gaskets

This item fits the following BMWs:
2004-2010 E60 BMW 545i 550i
2004-2010 E63 BMW 645ci 650i
2002-2008 E65 BMW 745i 745li 750i 750li
2004-2006 E53 BMW X5 4.4i X5 4.8is
2007-2013 E70 BMW X5 4.8i xDrive48i

An important adjustment component for the timing Valvetronic system, this part can cause poor engine performance if it fails. Replace your failed Adjusting Unit with an OEM VDO unit to restore smooth engine operation.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform

Upgrade your BMW's engine performance with the Genuine BMW E46 Inlet Camshaft. This high-quality camshaft is designed to optimize airflow and fuel delivery, resulting in improved horsepower and torque.

• Genuine BMW part for reliable performance
• Designed specifically for BMW E46 models
• Optimizes airflow and fuel delivery
• Improves horsepower and torque output