Turner Motorsport for BMW E36 (1992-1998) M3

NOW LOCATED UNDER T#339018

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to remedy this common issue with a set of Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. A unique knurled bushing design also ensures compatibility with the OEM sway bar, offering a first-to-market solution for enthusiasts looking to retain factory components.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits factory rear sway bars on E23, E24, E28, E30, and E36 Laser-etched markings for quick and easy adjustments

For many E30, E36, E28, and Z3 owners, the factory antenna is often a source of frustration. Many have stopped functioning entirely after forty years post-production. What's more, if your antenna is stuck at full height, it can ruin the clean lines of your vehicle’s rear end. The typical solution is a cheap grommet from the hardware store, which can lead to water/debris intrusion and more headaches down the road. Over the years, we've noticed the increase in demand for this modification, in addition to the issues associated with other, less optimized antenna delete pieces. Hours of research and development have culminated in a perfect-fit antenna delete plug—tailored specifically for your vintage BMW!

Our high-quality solution is engineered for durability, providing a sleek and watertight finish that restores the aesthetic of your car’s rear end while eliminating the need for an obsolete and likely disfunctional factory antenna.

Key Features:

Eliminates Factory Antenna: Solves issues associated with malfunctioning or broken antennas. Watertight Seal: This prevents water and debris from seeping into the trunk area, protecting against rust and corrosion. Enhanced Appearance: Streamlines the look of your BMW’s rear end for a more refined finish. Simple Installation: Installs in seconds without any tools required. Robust Construction: Made from quality low-density polyethylene for long-lasting durability. Precision Engineering:

The Turner Motorsport Antenna Delete was designed and rigorously tested by our in-house team of engineers in Wadsworth, Ohio. Utilizing state-of-the-art technology such as FARO laser scanning for precise reverse engineering, SolidWorks 3D CAD modeling, and extensive product testing, this delete solution offers exact fitment and top-tier quality you can trust.

• 55MM, 75MM, 90MM LENGTHS
• Black phosphorous corrosion resistant coating
• "OEM" appearance
• Full-length threads for more nut engagement in tight spaces
• Long shank for good brake rotor alignment
• Heat-treated aircraft quality alloy steel

Wheel studs are among the safest and most beneficial upgrades you can make on a track car. Not only are wheel studs safer than wheel bolts but they make changing wheels/tires much easier. One of the frustrating things about installing your wheels on the hub is that it's difficult to line up the wheel on the bolt holes. As wheels get larger but also heavier it's even more trouble. Add in a wheel spacer and the task is twice as hard. BMW does produce a wheel alignment pin for this purpose but if you're changing wheels often a stud conversion is the better way to go.

These wheel studs are the same as our hugely popular Bullet Nose studs but with threads along the full length of the stud. This gives you more threaded area for tightening wheel nuts or allows the use of a closed-end wheel nut. These also have a more OEM appearance. Although these are a lower cost version of our Bullet Nose studs, they are every bit as strong, durable, and safe. The Bullet Nose is an upgrade because it's easier to install and almost impossible to cross-thread a nut.

Not all wheel studs are created equal. We don't take a manufacturer's generic wheel stud from their catalog and call it our own. Turner Wheel Studs are designed to our own specifications and manufactured for us exclusively. Beware of cheaper studs on the market! We have seen other studs similar to our own designs that are not a true BMW fitment. There are differences that we have ironed out over our years of selling wheel studs for the BMW market. Our stud prices may be slightly higher than the rock bottom prices on the web but we promise that it's a higher quality.

Sold per stud.

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to address this common issue with Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. These end links feature a bolt-through bushing design, which is compatible with most adjustable aftermarket sway bars. Mounting hardware is included for easy installation.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits most aftermarket sway bars with bolt-through attachment Laser-etched markings for quick and easy adjustments