Packaged by Turner for BMW 3 Series E30 (1984-1991)

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this E30 BMW brake package are all of the OEM equivalent components needed to replace your Front & Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Pagid Front & Rear Brake Pads
• Zimmerman Front & Rear Rotors
• New Front & Rear Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
E30 BMW M3

• Cylinder Head Washer
• BMW Coolant / Antifreeze - 1 gallon
• Copper Exhaust Lock Nut
• Oil Filter
• Cylinder Head Bolt Set
• Engine Oil Drain Plug Washer
• Dielectric Spark Plug Boot Protector
• BMW TwinPower Turbo 5W-30 Engine Oil
• Cylinder Head Gasket
• Assembly Lube - 4 oz
• Engine Oil Drain Plug
• M20 Cylinder Head - complete

Drive line slop is often caused by faulty engine and transmission mounts. This can result in knocking noises under heavy acceleration, excessive vibration, and a less responsive feel in power. These Genuine BMW mounts are perfect to eliminate these problems and provide long lasting reliability.

Included in this kit:

• Genuine BMW Engine Mount (x2)
• OEM Lemforder Manual Transmission Mount (x2)

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Front Sway Bar End Links
Front Upper Strut Mounts
Control Arms w/ Bushings
Control Arm Brackets w/ M3 Control Arm Bushings
Outer Tie Rods

Regular maintenance is key to keeping your BMW running smoothly, and the water pump is a critical component that should be serviced every 60,000 miles. To ensure the overall efficiency of your cooling system, it's also recommended to replace the thermostat at the same time. Turner Motorsport has created a streamlined solution with their Water Pump & Thermostat Replacement Kit, making your cooling system upgrade simple and effective.

Kit Includes:

Meyle Water Pump with Metal Impeller (11510393338) VEMO Thermostat - 88°C (11537511580) Elring Thermostat Housing Flange Gasket (11531721172) Genuine BMW Coolant/Antifreeze (82141467704) Benefits:

Enhanced Cooling Efficiency: Earlier opening thermostat improves temperature control under performance conditions. Reliable Components: Includes high-quality parts from Meyle and VEMO, known for their durability and reliability. Complete Solution: All necessary components for a comprehensive cooling system refresh in one convenient kit. Performance-Driven Design: Ideal for those looking to maintain and enhance the cooling capabilities of their S55 engine.

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Sway Bar End Links
Reinforcement Plates
Shock Mounts & Gaskets
Differential Mount Bushing
Trailing Arm Bushings
Subframe Bushings

 The timing belt on the M20 engine should be replaced every 50,000 miles. The Gates Racing's timing belt this kit includes  is constructed of HNBR elastomeric composites. That being said, they are 300% stronger than the OE belt & deliver up to three times the heat resistance. Also included in this kit are the following:

• Gates Racing Timing Belt
• Tensioner
• Tensioner Spring and Bolt
• Water Pump & Gasket
• Thermostat & Gasket
• Camshaft Seal
• 1 Liter of Coolant
• Radiator Drain Plug

This kit includes sufficient coolant for a water pump replacement. If you intend to perform additional cooling system maintenance, pick yourself up an additional bottle of coolant.

For vehicles with production date up to 09/1987.

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

This is a compete cooling system overhaul kit, which includes all the common cooling system failure parts bundled into a complete package. This cooling system package is for the E30 325 with the M20 engine. 

A failure in the cooling system can lead to overheating and catastrophic engine failure. Don't gamble your engine! By replacing these core items preventatively, such as the thermostat housing, radiator, and waterpump, you are defusing what could be a ticking cooling system time bomb. And if you've had a failure of one of these parts, now is the time to refresh your entire cooling system. Keep on top of the cooling needs of your engine for your own piece of mind. Potential buyers also see the upside of a properly maintained car with receipts. 

This water pump fits the following BMWs: 
1998-1991 E30 BMW 325e 325es 325i 325ic 325is 325ix 

Anytime that you replace your front control arms (which should be often), you must replace your control arm bushings. The reason is because it's hard to tell if you're bushings are really bad and they are often destroyed when removed. These bushings have the hole in the center and came standard on the 318i/325i.

For convenience, we carry the steel bushing carrier brackets (part# TSU9995PB3) with new hardware which will save you downtime caused by pressing out the old bushings and pressing in the new bushings.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is

Restore your BMW's braking system to its original performance with this Packaged by Turner OE Front and Rear Brake Service Kit. Expertly crafted for precise fitment and dependable performance, this kit contains everything needed for a complete front and rear brake overhaul, ensuring maximum braking efficiency and safety.

Top Features:

Comprehensive Package: Includes premium brake pads, rotors, and all required hardware for a thorough front and rear brake service. OE Specification: Built to original equipment standards for perfect compatibility and exceptional performance. High-Quality Materials: Made from robust materials designed to endure high temperatures and reduce wear, guaranteeing long-lasting brake functionality. Improved Safety: Engineered to deliver consistent and powerful stopping power, enhancing overall vehicle safety and control. User-Friendly Installation: Comes with all necessary components for a smooth and easy installation process. Advantages:

Revitalizes Braking Performance: Upgrading worn-out parts with OE-standard components ensures your braking system operates at peak efficiency. Dependable Operation: Each part is precisely manufactured to meet or surpass original equipment specifications. Economical Maintenance: This all-inclusive kit provides a cost-effective solution for maintaining your vehicle’s brake system. Gain assurance with unmatched stopping power and reliability. Essential for preserving your vehicle's safety and performance, this kit is a must-have for any BMW owner's maintenance routine. For a detailed list of included components, please refer to the "Kit Contents" tab.

Over time, accessory belts begin to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belts and tensioners on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or over heated engine due to a bit of simple overlooked maintenance. This kit includes the belts and tensioner bar.

Fits the following BMWs:
1985-1991 E30 BWM M3