BMW Brakes & Brake Parts for BMW Z3 (1996-2002)

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

This caliper bushing kit will eliminate flex caused by weak rubber caliper bushings. As the brake pedal is pressed the caliper grabs the rotor and twists on its mounting bushings. The rubber bushings allow the caliper to deflect and twist which affects pedal feel and results in uneven pad wear. These solid brass bushings will not twist or deflect so your calipers can squeeze the pads evenly on both sides of the rotor (sort of like what multi-piston big brakes do). This will give you much longer pad life and a more consistent pedal feel. This is the most complete kit we have ever sold with stainless steel caliper slide bolts, o-rings, and new dust boots. Unlike other kits, these bushings are pressed into the caliper and will not shift or slide on their own.

Installation is straightforward: remove the old rubber bushings and press in the new brass bushings (we recommend special tool 003326ECS03). High temp caliper grease or anti-seize is required. The new bushings include an inner o-ring that helps trap grease on the slide bolt, reducing friction and wear.

***Click here for installation instructions*** 

***Click here for the installation tool***

For most models with floating calipers. Fits the rear of E90/2 and E60, but for the front you'll need the kit found here. Does not fit E30 models with Girling calipers, but is compatible with Ate calipers. 

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a proprietary zinc-nickel plating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this E36 BMW brake package are all of the OEM equivalent components needed to replace your Front & Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Pagid Front & Rear Brake Pads
• Pagid Front & Rear Rotors
• New Front & Rear Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
E36 BMW M3 S52/S50
Z3 BMW M Coupe/Roadster S52/S54

Front Drilled & Slotted Brake Rotors V5 - Set (315x28) are precision manufactured by Turner Motorsport to ensure consistent stopping power during high-performance driving. These 5th generation rotors are specifically designed for BMW vehicles and feature advanced technology for optimal braking performance. The rotors are coated with a matte black zinc finish, offering excellent corrosion protection and a sleek appearance.

The V5 design incorporates cross-drilled and slotted features, enhancing heat dissipation and wet-weather performance compared to traditional slotted rotors. This makes them an ideal choice for high-performance driving enthusiasts. The black zinc coating not only provides a modern look but also offers superior protection against corrosion.

• Enhanced Heat Dissipation: Cross-drilled and slotted design improves cooling, reducing brake fade.
• Improved Wet-Weather Performance: Better braking response in wet conditions for increased safety.
• Matte Black Zinc Coating: Provides a contemporary look and protects against corrosion.
• High-Quality Construction: Made from premium materials to withstand high-performance demands.
• Precision Machining: Ensures optimal rotor balance, reduces vibration, and delivers a smooth braking experience.

Enhance Your BMW's Braking Performance with ECS Tuning's Innovative Package

Upgrade the braking capabilities of your BMW E36 M3 or Z3M with ECS Tuning's advanced braking package. This solution prioritizes increased brake torque and thermal capacity, utilizing ECS 2-piece E46 M3 CSL rotors to deliver outstanding performance behind 18" wheels and compatible 17" big brake-friendly wheels.

Key Benefits:

• Custom-designed caliper bracket for fitting ECS 2-piece E46 M3 CSL rotors
• Lightweight aluminum hats for reduced weight and enhanced durability
• Gray cast iron rings for wear resistance and efficient heat dissipation
• 2-Piece semi-floating construction prevents rotor warping
• Heat-treated for increased strength and performance
• Directionally veined for accelerated cooling
• Drilled and slotted design for improved ventilation and cleaner brake pads
• Overall weight savings for improved braking and suspension performance
• High manufacturing quality for corrosion resistance and long-term durability

Installation is hassle-free, utilizing existing calipers, pads, lines, and hardware. Upgrade your pads simultaneously with a wide selection of E36 M3 or E46 M3 brake pads for enhanced performance.