BMW Engine Parts for BMW Z Series G29 (2019+)

Port Injector Plugs

T#:27171925

Part#: UNI-BMS-PIPLUGS

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

These dummy injectors fit in place of port injection fuel injectors to block the holes. Allows use to aluminum manifolds with port injection bungs without having to purchase fuel injectors. Plugs are EV14 injectors and measure 38mm or 1.5" from o-ring to o-ring.

Show More Show Less

Spark Plug Gapper Tool BMS Billet

T#:26404907

Part#: 12MMSPG

In Stock

$ 35.00 USD

Add to Wish List

Qty

$ 35.00 USD

Add to Wish List

Spark Plug Gapper Tool BMS Billet is essential for accurately adjusting the gap of spark plugs. This precision tool ensures that each plug is set to the exact specifications required for optimal engine performance. Made in the USA, it features a 12mm plug thread size, making it suitable for a wide range of applications.

Precision Adjustment: Allows for accurate gap adjustments to ensure optimal spark performance and engine efficiency.
Speed and Efficiency: Streamlines the process of gapping plugs while maintaining high precision, saving time and effort.
High-Quality Construction: Crafted from billet materials for durability and reliability, ensuring long-term use.
Lifetime Replacement Program: Comes with a lifetime replacement guarantee, reflecting confidence in the tool's quality and performance.

Upgrade your spark plug maintenance with the Spark Plug Gapper Tool BMS Billet for a reliable and precise solution.

Show More Show Less

Metal Oil Filter Housing Upgrade With Filter & Cooler - BMW B58TU (B...

T#:43378540

Part#: B58G2OFH

Back Ordered

$ 279.00 USD

Add to Wish List

Qty

$ 279.00 USD

Add to Wish List

Upgraded metal oil filter housing designed to replace the faulty stock housing which is known to crack.

Billet Oil Filter Cap

T#:21045500

Part#: BMS-BOFC

In Stock

Starting at $ 79.00 USD

Add to Wish List

Starting at $ 79.00 USD

Add to Wish List

The Burger Motorsports billet aluminum B58 oil filter cover directly replaces your weak OE plastic cap for greater protection, ease of removal/install, and great looks under the hood. You can use a 3/8" inch drive ratchet or torque wrench to install and remove. The built-in 32mm hex head does not require a special removal/install tool like the factory cap. Uses the OE oil filter, filter housing o-ring, and filter insert. Anodized for protection. This quality part is a must for any serious BMW owner. Install: After removing the OEM oil filter cap, remove the filter and be sure to remove the plastic oil filter bypass valve and transfer it to the new BMS billet oil filter cap. Be sure to replace the exterior o-ring gasket also when installing. Features and Benefits Solid aluminum design is much stronger than brittle plastic Integrated heat sinks for better oil cooling Special tools are not required for removal/install like the factory cap Strong design won't fail under pressure Reuses OE filter insert and o-ring Anodized for protection Looks great under the hood Available in black, red, silver, and blue Made in the USA

Show More Show Less

Billet Spark Plug Gapper Tool - 14mm - BMS

T#:583132

Part#: BMSBSPGT14MM

Ships in 7 Business Days

$ 35.00 USD

Add to Wish List

Qty

$ 35.00 USD

Add to Wish List

BMS Billet Spark Plug Gapper Tool - 14mm is an essential tool for achieving accurate and consistent spark plug gapping, ideal for automotive enthusiasts and professional mechanics alike. This precision tool helps maintain optimal plug performance by providing reliable, consistent gaps. Available in both 14mm and 12mm plug thread sizes, this tool is proudly made in the USA to deliver durability and precision.

Precisely gaps spark plugs for enhanced engine performance and efficiency
Speeds up the gapping process while ensuring accuracy and uniformity
Available in two sizes (14mm and 12mm) for a wider range of compatibility
Optional specialty feeler gauge included with 4 blades in thicknesses of .018, .020, .022, and .024
Made in the USA for premium quality and durability

Show More Show Less

BMS JB4 Port Injection Controller - F/G Chassis

T#:21012590

Part#: F-G-PORTINJCONMO

No longer available

The Burger Motorsports JB4 Port Injection Controller attaches to the JB4 allowing it to directly control both traditional port injection kits and WMI port injection kits. The JB4 port injection controller is a fully integrated solution allowing enhanced port injection mapping and safety. For example the JB4 port injection controller: 1) Uses low fuel pressure in conjunction with boost pressure to evaluate injection pressure and adjust PI IPW dynamically as required to maintain consistent flow volume. This becomes particularly important in applications that are at the edge of their low fuel pressure supply. As low pressure drops or oscillates port injection IPW must be dynamically adjusted to avoid run lean conditions. 2) Monitors pedal input, clutch input, gear, throttle position, etc, allowing more advanced mapping and instant cut of PI when letting off the gas or when traction control kicks in to avoid backfires. 3) Monitors AFR in both banks and can cut PI flow in the event a misfire event is detected preventing a potentially lean condition. 4) Monitors current through the injectors and sends a signal back to the JB4 altering it of various problems including a clogged or disconnected injector, blown electrical fuse, loose ground, etc. 5) Monitors fuel trims in each bank and failsafe's in the event of a mismatch of more than 15% indicating a potential boost single cylinder boost leak or injector flow issue. 6) Allows easy user adjustment of overall fuel volume using linear "Fuel Bias 0-100" values by RPM, greatly reducing the typical mapping complications when making manual tuning changes. 7) Integrates into the JB4 multi-map system which produces on-the-fly PI mapping changes when you change maps when boost is reduced in lower gears, or during anti-lag engagement. 8) When equipped with a JB4 integrated flex fuel sensor or JB4 virtual flex fuel sensor can automatically adjust port injection volume based on the E85 mixture allowing for easy mixture changes. 9) Enhanced mapping logic such as tip in supplement to boost port injection during sudden transitions like spool up or gear changes where the high-pressure pump tends to have problems keeping up. 10) Does not require a separate interface and cable for mapping and tuning port injection. It's all done right through the JB4 interface and logs greatly simplifying the process. 11) Includes an extra output to run your second fuel pump OR WMI PUMP (for port injection meth), eliminating the need for an extra Hobbs switch.

Show More Show Less

JB4PRO Flex Fuel Add On Harness - B58/S58

T#:49822568

Part#: JB4PB58FFAOH

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

Take your B58 or S58 build further with the JB4PRO Flex Fuel Add-On Harness—a simple, plug-and-play way to add an ethanol sensor and optional fuel pressure sensor to your JB4PRO setup. Keep your install clean, your wiring organized, and your tune dialed to match every fuel blend in the tank. Why it matters: Plug & Play: Connects directly to your JB4PRO—no cutting or splicing required. Sensor Ready: Supports ethanol and fuel pressure sensors for precise, real-time fueling adjustments. Clean, Safe Installation: Includes a 12 V adapter and inline fuse for hassle-free integration. How it works: This harness links your JB4PRO tuner to your flex fuel hardware. It’s not a complete flex fuel kit—you still need a compatible ethanol sensor—but it gives your JB4PRO the accurate readings it needs to adjust timing, boost, and fueling for E30, E50, or E85 blends.

Show More Show Less

Mubea Mechanical Accessory Belt Tensioner - BMW B46/48 B58 ...

For vehicles without the Energy Recovery System

T#:26971839

Part#: 11288580360

Ships in 1 Business Day

$ 177.99

This product was last offered at the strikethrough price on
05-07-2026

$ 158.99 USD

Add to Wish List

Qty

$ 158.99 USD

Add to Wish List

Accessory belt tensioners provide tension to the belt drive system, ensuring the belt is able to properly turn engine accessories without slipping. If your tensioner has failed, replace it with a brand-new unit to ensure proper water pump and alternator functionality.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW Z Series G29 (2019+)

Sub-Categories

Port Injector Plugs

Spark Plug Gapper Tool BMS Billet

Metal Oil Filter Housing Upgrade With Filter & Cooler - BMW B58TU (B...

Billet Oil Filter Cap

Billet Spark Plug Gapper Tool - 14mm - BMS

BMS JB4 Port Injection Controller - F/G Chassis

JB4PRO Flex Fuel Add On Harness - B58/S58

Mubea Mechanical Accessory Belt Tensioner - BMW B46/48 B58 ...

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Narrow Results