BMW Engine Parts for BMW X Series F26 (2015+)

Clear BMW chassis

Please ensure your correct model is selected

Turner Motorsport has everything you need to upgrade your BMW through our stages of performance or to keep your car in peak condition with our range of the latest in proven OEM cooling parts. Upgrade your cooling system and engine performance with the selections below to give your BMW a performance and reliability advantage.

Sub-Categories

Sort By:

Rein - Corporate Logo
T#:379282
Part#: 11132210959
In Stock
$ 44.89 USD
Free Shipping on orders $49 and up

This is a replacement set of bolts for the oil pan on your BMW equipped with an M54, N52, N54, or N55. The stock bolts are easy to strip, break, or even lose. Replace your missing or damaged bolts with all new hardware from OEM Rein to ensure a tight seal all around your oil pan and prevent oil leaks.

Check fitment with our guide above to ensure these are the oil pan bolts required for your vehicle.

Show More Show Less
Burger Motorsports - Corporate Logo
T#:21045489
Part#: BMS-OFC
In Stock
Starting at $ 89.00 USD
Free Shipping on orders $49 and up
Starting at $ 89.00 USD
Free Shipping on orders $49 and up
The Burger Motorsports V2 billet aluminum oil filter cover is a metal upgrade that directly replaces your weak OE plastic cap for greater protection, better cooling, ease of removal/install, and looks great under the hood. The built-in 21mm hex and a 3/8" drive socket wrench fitting that does not require a special removal/install tool like the factory cap. Uses the OE oil filter, filter housing o-ring, and filter cage. Anodized for protection. This quality part is a must for any serious BMW owner. Replaces OEM part number 11427525334 - BMW Oil filter cover. Features and Benefits Solid aluminum design is much stronger than brittle plastic 21mm hex head + 3/8" drive socket wrench fitting Integrated heat sinks for better oil cooling Special tools are not required for removal/install like the factory cap Strong design won't fail under pressure Reuses OE filter cage and o-ring Anodized for protection Looks great under the hood Made in the USA
Show More Show Less
Burger Motorsports - Corporate Logo
T#:27171925
Part#: UNI-BMS-PIPLUGS
In Stock
$ 60.00 USD
Free Shipping on orders $49 and up
These dummy injectors fit in place of port injection fuel injectors to block the holes. Allows use to aluminum manifolds with port injection bungs without having to purchase fuel injectors. Plugs are EV14 injectors and measure 38mm or 1.5" from o-ring to o-ring.
Show More Show Less

Burger Motorsports - Corporate Logo
T#:26404907
Part#: 12MMSPG
In Stock
$ 35.00 USD
Free Shipping on orders $49 and up

Spark Plug Gapper Tool BMS Billet is essential for accurately adjusting the gap of spark plugs. This precision tool ensures that each plug is set to the exact specifications required for optimal engine performance. Made in the USA, it features a 12mm plug thread size, making it suitable for a wide range of applications.

  • Precision Adjustment: Allows for accurate gap adjustments to ensure optimal spark performance and engine efficiency.
  • Speed and Efficiency: Streamlines the process of gapping plugs while maintaining high precision, saving time and effort.
  • High-Quality Construction: Crafted from billet materials for durability and reliability, ensuring long-term use.
  • Lifetime Replacement Program: Comes with a lifetime replacement guarantee, reflecting confidence in the tool's quality and performance.

Upgrade your spark plug maintenance with the Spark Plug Gapper Tool BMS Billet for a reliable and precise solution.

Show More Show Less

Rein - Corporate Logo
T#:34114257
Part#: 11127570292
In Stock
$ 254.99 USD
Free Shipping
$ 254.99 USD
Free Shipping

Valve Cover by Rein is a crucial component designed to protect and seal the top of your BMW’s engine, ensuring optimal performance and preventing oil leaks. Engineered specifically for BMW engines, this high-quality valve cover provides a precise fit and exceptional durability. Available at Turner Motorsport, the Valve Cover by Rein offers long-lasting reliability, protecting critical engine components from damage while maintaining proper oil pressure.

  • Designed specifically for BMW engines for perfect fit and function
  • Prevents oil leaks, maintaining proper engine lubrication
  • Made from high-quality, durable materials for long-lasting performance
  • Direct-fit replacement ensures hassle-free installation
  • Protects critical engine components and improves engine efficiency
  • Helps maintain proper oil pressure for optimal engine performance

The Valve Cover VCE0101 by Rein from Turner Motorsport is the ideal solution for BMW owners seeking to protect their engine, prevent oil leaks, and ensure reliable performance.

Show More Show Less
Burger Motorsports - Corporate Logo
T#:21933055
Part#: N54PIIMINJECT
In Stock
$ 988.00 USD
$ 988.00 USD

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel Line Kit - Phoenix Racing is a high-performance upgrade engineered to replace the stock plastic intake manifold on BMW N54 engines. Constructed from durable, lightweight aluminum, this manifold increases airflow and strength, delivering reliable performance for both street and track applications. Integrated with top-mount port injection bungs, this manifold ensures optimal fuel delivery and spray patterns for maximum efficiency. The Phoenix Racing kit includes calibrated 750cc injectors and a plug-and-play fuel line, making it ideal for drivers aiming for high horsepower and seamless installation. Available through Turner Motorsport.

  • Replaces the factory plastic manifold with high-strength aluminum for increased durability and performance
  • Supports increased airflow to enhance engine power and efficiency
  • Integrated top-mount port injection bungs optimize fuel injector spray and delivery
  • Includes calibrated 750cc injectors and plug-and-play fuel line for a complete port injection solution
  • Multiple expansion vacuum ports support blow-off valves, boost gauges, Hobb’s switches, and more
  • High-quality, high-temperature o-rings provide lasting durability and reliability
  • Exclusively available through Turner Motorsport, ensuring trusted quality and service
Show More Show Less

Rein - Corporate Logo
T#:17738375
Part#: 13537585426
In Stock
$ 44.99 USD
Free Shipping on orders $49 and up
Ensures that proper pressure is maintained between the high-pressure fuel pump and fuel rail.
Rein - Corporate Logo
T#:594381
Part#: 11127588417
Ships in 3 Business Days
$ 84.99

This product was last offered at the strikethrough price on
08-12-2026

$ 59.00 USD
Free Shipping on orders $49 and up
$ 59.00 USD
Free Shipping on orders $49 and up
Connects to the PCV outlet on the valve cover

Rein - Corporate Logo
T#:17771585
Part#: 11428626653
In Stock at Vendor
$ 53.99 USD
Free Shipping on orders $49 and up
Rein OE quality return pipe is manufactured with premium rubber and is designed to be a direct-fit replacement.

Burger Motorsports - Corporate Logo
T#:583132
Part#: BMSBSPGT14MM
Ships in 7 Business Days
$ 35.00 USD
Free Shipping on orders $49 and up

BMS Billet Spark Plug Gapper Tool - 14mm is an essential tool for achieving accurate and consistent spark plug gapping, ideal for automotive enthusiasts and professional mechanics alike. This precision tool helps maintain optimal plug performance by providing reliable, consistent gaps. Available in both 14mm and 12mm plug thread sizes, this tool is proudly made in the USA to deliver durability and precision.

  • Precisely gaps spark plugs for enhanced engine performance and efficiency
  • Speeds up the gapping process while ensuring accuracy and uniformity
  • Available in two sizes (14mm and 12mm) for a wider range of compatibility
  • Optional specialty feeler gauge included with 4 blades in thicknesses of .018, .020, .022, and .024
  • Made in the USA for premium quality and durability
Show More Show Less
Rein - Corporate Logo
T#:594483
Part#: 11127588412
In Stock
Sale - Save 7% $ 326.99

This product was last offered at the strikethrough price on
07-15-2026

$ 304.41 USD
Free Shipping
Sale - Save 7%
$ 326.99

This product was last offered at the strikethrough price on
07-15-2026

$ 304.41 USD
Free Shipping
Burger Motorsports - Corporate Logo
T#:21012590
Part#: F-G-PORTINJCONMO
No longer available
No longer available
The Burger Motorsports JB4 Port Injection Controller attaches to the JB4 allowing it to directly control both traditional port injection kits and WMI port injection kits. The JB4 port injection controller is a fully integrated solution allowing enhanced port injection mapping and safety. For example the JB4 port injection controller: 1) Uses low fuel pressure in conjunction with boost pressure to evaluate injection pressure and adjust PI IPW dynamically as required to maintain consistent flow volume. This becomes particularly important in applications that are at the edge of their low fuel pressure supply. As low pressure drops or oscillates port injection IPW must be dynamically adjusted to avoid run lean conditions. 2) Monitors pedal input, clutch input, gear, throttle position, etc, allowing more advanced mapping and instant cut of PI when letting off the gas or when traction control kicks in to avoid backfires. 3) Monitors AFR in both banks and can cut PI flow in the event a misfire event is detected preventing a potentially lean condition. 4) Monitors current through the injectors and sends a signal back to the JB4 altering it of various problems including a clogged or disconnected injector, blown electrical fuse, loose ground, etc. 5) Monitors fuel trims in each bank and failsafe's in the event of a mismatch of more than 15% indicating a potential boost single cylinder boost leak or injector flow issue. 6) Allows easy user adjustment of overall fuel volume using linear "Fuel Bias 0-100" values by RPM, greatly reducing the typical mapping complications when making manual tuning changes. 7) Integrates into the JB4 multi-map system which produces on-the-fly PI mapping changes when you change maps when boost is reduced in lower gears, or during anti-lag engagement. 8) When equipped with a JB4 integrated flex fuel sensor or JB4 virtual flex fuel sensor can automatically adjust port injection volume based on the E85 mixture allowing for easy mixture changes. 9) Enhanced mapping logic such as tip in supplement to boost port injection during sudden transitions like spool up or gear changes where the high-pressure pump tends to have problems keeping up. 10) Does not require a separate interface and cable for mapping and tuning port injection. It's all done right through the JB4 interface and logs greatly simplifying the process. 11) Includes an extra output to run your second fuel pump OR WMI PUMP (for port injection meth), eliminating the need for an extra Hobbs switch.
Show More Show Less


Rein - Corporate Logo
T#:592203
Part#: 17127646150
Ships in 3 Business Days
$ 47.99 USD
Free Shipping on orders $49 and up
$ 47.99 USD
Free Shipping on orders $49 and up
Doing a cooling system refresh, or just replacing worn out and soft old hoses? Why settle for stock when you can get the added life and heat tolerance of silicone hoses? Retains OEM fitment without the OEM hose flaws, silicone will resist breaking down and getting soft as coolant heat cycles and will last longer than the OEM rubber hoses.
Show More Show Less
Burger Motorsports - Corporate Logo
T#:21045480
Part#: BMS-TLID
Ships in 1 Business Day
Starting at $ 39.00 USD
Free Shipping on orders $49 and up
Starting at $ 39.00 USD
Free Shipping on orders $49 and up
These billet CNC replacement aluminum oil thermostat lids and caps are an excellent way to add some color and style to your N54 N55 S55 engine bay. Anodized black, red or blue. Easy to install and made in the USA. Can be used with or without the BMS Sport Oil Cooler Valve.
Show More Show Less
Rein - Corporate Logo
T#:34214779
Part#: 11318648732KT5
Back Ordered
$ 1,205.99

This product was last offered at the strikethrough price on
04-28-2026

$ 1,156.99 USD
$ 1,156.99 USD

Rein Timing Chain Rebuild Kit - CKP0250 is a top-quality solution for BMW owners looking to maintain or restore the performance of their engine. Specifically designed for BMW models, this rebuild kit addresses common timing chain issues such as stretching and wear, which can lead to serious engine damage if not attended to. Available from Turner Motorsport, this kit provides all the necessary components for a complete timing chain replacement, ensuring your BMW continues to run smoothly and reliably.

The Rein Timing Chain Rebuild Kit - CKP0250 includes high-quality, durable parts that meet or exceed OEM standards. Whether you're a professional mechanic or a DIY enthusiast, this kit offers a comprehensive solution to ensure your engine’s long-term health and performance.

  • Specifically designed for BMW engines prone to timing chain issues
  • Complete rebuild kit includes timing chain, tensioner, and guides
  • Prevents costly engine damage due to worn or stretched timing chains
  • Made from high-quality materials for long-lasting durability
  • Meets or exceeds OEM specifications for reliable fitment and performance
  • Ideal for BMW maintenance, repairs, or engine rebuild projects

For BMW owners looking for a reliable, all-in-one solution, the Rein Timing Chain Rebuild Kit - CKP0250 from Turner Motorsport ensures your engine stays in optimal condition.

Show More Show Less

Burger Motorsports - Corporate Logo
T#:27171935
Part#: IRTHERM
Back Ordered
Starting at $ 318.99 USD
Free Shipping on orders $49 and up
Starting at $ 318.99 USD
Free Shipping on orders $49 and up
Precise Oil Temperature Control for Your BMW Upgrade your BMW N20, N26, N51, N52, N53, N54, N55, and S55 engine's oil temperature control with Improved Racing's high-performance oil cooler adapter. Designed to address flaws in the factory's restrictive oil cooler adapter and faulty internal flow control valve, this upgrade ensures precise oil temperature control. Improved Racing's thermostat provides quick engine warmup, prevents overcooling, and delivers full oil cooling capacity on demand. Trusted by professional race teams around the globe, Improved Racing's thermostats have proven highly reliable, are backed by a lifetime warranty, and are made in the USA. Option to Use the Factory Oil Cooler and Lines The optional factory oil line adapter allows you to use the factory oil cooler lines for a simple, plug-and-play installation. For maximum performance, the factory oil cooler and lines may be replaced with an aftermarket cooler and AN lines using the AN adapter fittings (-10AN line size is recommended). ​Please note that some applications, such as most BMW SUV's, use a water-to-oil heat exchangers. These applications require plugging the coolant supply and return ports, as well as adding an external air-to-oil cooler and lines (factory or aftermarket). Please note the Oil cooler adapter cannot be used without an oil cooler.
Show More Show Less

Rein - Corporate Logo
T#:45791744
Part#: 11367524954
In Stock
$ 8.99 USD
Free Shipping on orders $49 and up
The VANOS camshaft adjuster bolt is a single-use item that needs to be replaced any time it is removed. This replacement OEM Rein bolt is the perfect option to get your VANOS system reassembled and your BMW back on the road.
Show More Show Less

TechSelect Turbocharger Hose Kit
For vehicles with production date from 2015-2018
Rein - Corporate Logo
T#:14023868
Part#: TRK0011
Back Ordered
$ 349.99

This product was last offered at the strikethrough price on
08-12-2026

$ 305.99 USD
Free Shipping on orders $49 and up
$ 305.99 USD
Free Shipping on orders $49 and up
TechSelect Turbo Kits include all hoses, hardware and gaskets needed TechSelect Turbo Kit hoses are direct replacements to the OE, and include brackets, hardware and sealing components This hardware is designed and manufactured to withstand the rigorous operating environments of turbocharger systems Gaskets included are direct replacements to the OE ensuring optimal performance
Show More Show Less
Rein - Corporate Logo
T#:45997533
Part#: VCE0103
In Stock at Vendor
$ 287.99 USD
Free Shipping on orders $49 and up
If your valve cover is cracked or warped, replace it with this OEM Rein valve cover to eliminate oil and vacuum leaks.

Rein - Corporate Logo
T#:45791731
Part#: 11137601942
In Stock at Vendor
$ 336.99

This product was last offered at the strikethrough price on
05-15-2026

$ 327.99 USD
$ 327.99 USD
If your oil pan is dented, cracked, or damaged in any other way, it is important that you replace it as soon as possible. A leaking oil pan can result in rapid oil loss and eventual oil starvation, which can destroy an engine in seconds. This kit from OEM Rein includes a new oil pan, oil pan gasket, oil level sensor gasket, and xDrive axle seals, making your oil pan replacement much easier.
Show More Show Less

TechSelect Turbocharger Hose Kit
For vehicles with a production date of 06/2013+
Rein - Corporate Logo
T#:14122741
Part#: TRK0014
Back Ordered
$ 368.99

This product was last offered at the strikethrough price on
08-12-2026

$ 364.99 USD
Free Shipping on orders $49 and up
$ 364.99 USD
Free Shipping on orders $49 and up
TechSelect Turbo Kits include all hoses, hardware and gaskets needed TechSelect Turbo Kit hoses are direct replacements to the OE, and include brackets, hardware and sealing components This hardware is designed and manufactured to withstand the rigorous operating environments of turbocharger systems Gaskets included are direct replacements to the OE ensuring optimal performance
Show More Show Less
Burger Motorsports - Corporate Logo
T#:42133542
Part#: BMW-N55-PRM-950
Back Ordered
$ 1,138.00 USD
$ 1,138.00 USD
OEM Rein Valve Cover Kit - BMW N55 3.0L
For vehicles with Blow-by Heater option (S4NEA)
Rein - Corporate Logo
T#:45757477
Part#: 11127570292K
In Stock at Vendor
$ 352.99 USD
$ 352.99 USD
This Rein valve cover kit includes a new valve cover assembly, oil cap, and a vent hose. Over time, valve cover gaskets can fail, and plastic valve covers can warp and become brittle, leading to cracks. If your valve cover has cracked or warped, replace it early to prevent leaks and further valvetrain damage.
Show More Show Less


Rein - Corporate Logo
T#:46134810
Part#: CPL0054
In Stock
$ 28.99 USD
Free Shipping on orders $49 and up
Over time, has the cap for your oil filter housing become harder to remove? Using the wrong tool can round the top of the cap, making removal harder each time. Replace your old cap and seal to ensure your engine is leak-free. We recommend pairing this with the Schwaben Oil Filter Cap Tool (T#371924) to make installation and removal easier.
Show More Show Less